D-Link DIR-845L Page 43 User Manual Download

Page: 43 / 155

D-Link DIR-845L User Manual

Section 3 - Configuration

Maximum Idle Time:

Enter a maximum idle time during which the Internet connection is maintained during inactivity.

DNS Mode:

This option allow the router to obtain the DNS IP addresses from the ISP, when

Receive.DNS.from.ISP

is selected,

or allows the user to enter DNS IP address manually, when

Enter.DNS.Manually

is selected.

Primary DNS Server:

Enter the Primary DNS IP address used here.

Secondary DNS Server:

Enter the Secondary DNS IP address used here. This field is normally optional. Only one DNS address is required for

a functional Internet connection, but using a second DNS address provides more stability.

MTU:

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP.

1492 is the default MTU.

MAC Address:

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It

is not recommended that you change the default MAC address unless required by your ISP. You can use the

Clone.

Your.PC’s.MAC.Address

button to replace the Internet port’s MAC address with the MAC address of your Ethernet

card.

Summary of Contents for DIR-845L




























































































































































Search results

Summary of Contents for DIR-845L

Reviews:

Related manuals for DIR-845L

Brands by name

Popular brands

D-Link DIR-845L, User Manual

Search results

Summary of Contents for DIR-845L

Reviews:

Related manuals for DIR-845L

Brands by name

Popular brands