D-Link DIR-845L Page 15 User Manual Download

Page: 15 / 155

D-Link DIR-845L User Manual

Section 2 - Installation

Note:

It is strongly recommended to replace your existing router with the DIR-845L instead of using both. If your modem is a combo

router, you may want to contact your ISP or manufacturer’s user guide to put the router into Bridge mode, which will ‘turn off’ the

router (NAT) functions.

If you are connecting the DIR-845L router to an existing router to use as a wireless access point and/or switch, you will have

to do the following to the DIR-845L before connecting it to your network:

• Disable UPnP

™

• Disable DHCP

• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept

a DHCP address from your other router.

To connect to another router, please follow the steps below:

1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure

your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the

Networking.Basics

section for more information. If you need to change the settings, write down your existing settings before making any

changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have

to do anything to your computer.

2. Open a web browser, enter

http://dlinkrouter.local

and press

Enter

. When the login window appears, set the user name

Admin

and leave the password box empty. Click

Log.In

to continue.

3. Click on

Advanced

and then click

Advanced.Network

. Uncheck the

Enable.UPnP

checkbox. Click

Save.Settings

to continue.

4. Click

Setup

and then click

Network.Settings

. Uncheck the

Enable.DHCP.Server

checkbox. Click

Save.Settings

to continue.

Connect to an Existing Router

Summary of Contents for DIR-845L




























































































































































Search results

Summary of Contents for DIR-845L

Reviews:

Related manuals for DIR-845L

Brands by name

Popular brands

D-Link DIR-845L, User Manual

Search results

Summary of Contents for DIR-845L

Reviews:

Related manuals for DIR-845L

Brands by name

Popular brands