D-Link DIR-845L Page 11 User Manual Download

Page: 11 / 155

D-Link DIR-845L User Manual

Section 2 - Installation

Before you Begin

Installation

This section will walk you through the installation process. Placement of the router is very important. Do not place the router

in an enclosed area such as a closet, cabinet, or in the attic or garage.

• Please configure the router with the computer that was last connected directly to your modem.

• You can only use the Ethernet port on your modem. If you were using the USB connection before using the router,

then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port

on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection

types (USB to Ethernet).

• If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet,

Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.

Summary of Contents for DIR-845L




























































































































































Search results

Summary of Contents for DIR-845L

Reviews:

Related manuals for DIR-845L

Brands by name

Popular brands

D-Link DIR-845L, User Manual

Search results

Summary of Contents for DIR-845L

Reviews:

Related manuals for DIR-845L

Brands by name

Popular brands