manualshive.com logo in svg

D-Link DGS-3224SR, Command Line Interface Reference Manual

The D-Link DGS-3224SR is a high-performance switch designed for network professionals. Enhance your network configuration skills with the Command Line Interface Reference Manual, available for free download at manualshive.com. This comprehensive manual offers detailed instructions to optimize your networking experience. Get started today and unlock the full potential of your D-Link switch.

Share
Download
background image

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide 

94

Command Parameters 

ipaddress <ipaddr> | state [enable | disable]} 

Create syslog 

{host(1) [all|<index 1-4>] { severity 
[informational | warning | all] | facility [local0 | 
local1 | local2 | local3 | local4 | local5 |local6 | 
local7] |  |udp_port <udp_port_numer> | 
ipaddress <ipaddr> | state [enable | disable]} 

Delete syslog 
host 

[<index 1-4> |all] 

Show syslog 
host 

{index 1-4>} 

 

Each command is listed, in detail, in the following sections. 

 

show packet ports 

Purpose 

Used to display statistics about the packets 
sent and received by the switch. 

Syntax 

show packet ports <portlist> 

Description 

This command is used to display statistics 
about packets sent and received by ports 
specified in the port list. 

Parameters 

<portlist>  

−

  specifies a range of ports to be 

configured. The port list is specified by 
listing the beginning port number and the 
highest port number of the range.  

The DGS3224SR is a stackable switch and 
each port is designated as belonging to a 
particular switch in the stack. For example, 

Summary of Contents for DGS-3224SR



























































































































































































































































































Reviews:

No comments

Related manuals for DGS-3224SR

Patton electronics 3210 Specification Sheet preview
3210
Brand: Patton electronics Pages: 2
H3C MSR 20-20 Supplementary Manual preview
MSR 20-20
Brand: H3C Pages: 6
3Com OfficeConnect 3CP4144 How To Set Up preview
OfficeConnect 3CP4144
Brand: 3Com Pages: 4
3Com OfficeConnect 3CP4144 Release Note preview
OfficeConnect 3CP4144
Brand: 3Com Pages: 2
H3C MSR 20-20 User Manual preview
MSR 20-20
Brand: H3C Pages: 60
H3C MSR 20 Series Manual preview
MSR 20 Series
Brand: H3C Pages: 149
3Com 3C13636 Installation Manual preview
3C13636
Brand: 3Com Pages: 27
3Com OfficeConnect 3C19500 User Manual preview
OfficeConnect 3C19500
Brand: 3Com Pages: 52
3Com NJ220 - IntelliJack Switch User Manual preview
NJ220 - IntelliJack Switch
Brand: 3Com Pages: 82
B&B Electronics Conel UR5i v2 Libratum User Manual preview
Conel UR5i v2 Libratum
Brand: B&B Electronics Pages: 32
Allied Telesis AR725 Quick Start Manual preview
AR725
Brand: Allied Telesis Pages: 22
IBM CFFh Installation Manual preview
CFFh
Brand: IBM Pages: 34
NETGEAR RH328 Reference Manual preview
RH328
Brand: NETGEAR Pages: 142
Cabletron Systems SmartSTACK ELS100-24TXM Installation And User Manual preview
SmartSTACK ELS100-24TXM
Brand: Cabletron Systems Pages: 117
ADIC FCR 200 Operator'S Manual preview
FCR 200
Brand: ADIC Pages: 140
NetComm 4GM3W User Manual preview
4GM3W
Brand: NetComm Pages: 65
Abocom WR5205G User Manual preview
WR5205G
Brand: Abocom Pages: 59
Lantech TMR-5002 User Manual preview
TMR-5002
Brand: Lantech Pages: 23

Brands by name

Popular brands

Load more brands