manualshive.com logo in svg

D-Link DGS-3224SR, Command Line Interface Reference Manual

The D-Link DGS-3224SR is a high-performance switch designed for network professionals. Enhance your network configuration skills with the Command Line Interface Reference Manual, available for free download at manualshive.com. This comprehensive manual offers detailed instructions to optimize your networking experience. Get started today and unlock the full potential of your D-Link switch.

Share
Download
background image

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide 

222

DGS-3224SR:4# 

 

 

show auth_statistics 

Purpose 

Used to display the switch’s authentication 
statistics. 

Syntax 

show auth_statistics {ports <portlist>} 

Description 

The show auth_statistics command is used 
to display authentication statistics. 

Parameters 

ports <portlist> 

−

 Specifies a range of ports. 

The portlist is specified by listing the lowest 
switch number and the beginning port 
number on that switch, separated by a 
colon. Then the highest switch number, 
and the highest port number of the range 
(also separated by a colon) are specified. 
The beginning and end of the portlist range 
are separated by a hyphen. For example, 
1:3 would specify switch number 1, port 3; 
2:4 specifies switch number 2, port 4. 
Thus, 1:3-2:4 specifies all of the ports 
between switch 1, port 3 and switch 2, port 
4, in numerical order. 

Restrictions None. 

 

Example Usage: 

To display authentication statistics: 

DGS-3224SR:4#show auth_statistics ports 1 
Command: show auth_statistics 
 

Port number : 1:1 

Summary of Contents for DGS-3224SR



























































































































































































































































































Reviews:

No comments

Related manuals for DGS-3224SR

Garmin GND 10 Installation Instructions preview
GND 10
Brand: Garmin Pages: 2
Hama 53107 Operating Instruction preview
53107
Brand: Hama Pages: 10
AlphaShield INTERNET PRIVACY PROTECTION (Spanish) Manual Del Usuario preview
INTERNET PRIVACY PROTECTION
Brand: AlphaShield Pages: 49
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Brand: ADC Pages: 7
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Brand: Ubiquiti Pages: 13
Zigen IP-Logic ZIG-IPPRO-RX Quick Start Manual preview
IP-Logic ZIG-IPPRO-RX
Brand: Zigen Pages: 4
Tripp Lite N310-30M Specification Sheet preview
N310-30M
Brand: Tripp Lite Pages: 2
UNICOM DynaGST/2402G GEP-33224T-1 User Manual preview
DynaGST/2402G GEP-33224T-1
Brand: UNICOM Pages: 17
LevelOne FSW-0512 Specification Sheet preview
FSW-0512
Brand: LevelOne Pages: 2
EMC VNX5300 Block Hardware Information Manual preview
VNX5300 Block
Brand: EMC Pages: 88
ZyXEL Communications Prestige 643 User Manual preview
Prestige 643
Brand: ZyXEL Communications Pages: 191
ActionTec MI424WR MI424WR Upgrade Procedure preview
MI424WR
Brand: ActionTec MI424WR Pages: 3
Erbauer 3663602796282 Original Instructions Manual preview
3663602796282
Brand: Erbauer Pages: 36
Parker Sporlan Division SCS-PB Series Installation And Operating Instructions Manual preview
Sporlan Division SCS-PB Series
Brand: Parker Pages: 10
H3C SecPath L5030 Installation Manual preview
SecPath L5030
Brand: H3C Pages: 62
Inter-m S- Media Manual preview
S- Media
Brand: Inter-m Pages: 20
Alloy POEGE24T User Manual preview
POEGE24T
Brand: Alloy Pages: 13
Me VS-M1 Instructions Manual preview
VS-M1
Brand: Me Pages: 28

Brands by name

Popular brands

Load more brands