D-Link DGS-3224SR Command Line Interface Reference Manual Download

Page: 235 / 282

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

235

create access_profile

src_port_mask <hex 0x0-0xffff>

−

Specifies a UDP port mask for the source
port.
dst_port_mask <hex 0x0-0xffff>

−

Specifies a UDP port mask for the
destination port.

protocol_id

−

Specifies that the switch will

examine each frame’s Protocol ID field.

user_mask <hex 0x0-0xffffffff>

−

Specifies that the rule applies to the IP
protocol ID and the mask options behind
the IP header.

permit

−

Specifies that packets that match

the access profile are permitted to be
forwarded by the switch.
deny

−

Specifies that packets that do not

match the access profile are not permitted
to be forwarded by the switch and will be
filtered.
profile_id <value 1-8>

−

Specifies an index

number that will identify the access profile
being created with this command.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To create access list rules:

Command: create access_profile ethernet vlan source_mac 00-
00-00-00-00-01 destin
ation_mac 00-00-00-00-00-02 802.1p ethernet_type permit
profile_id 8

Summary of Contents for DGS-3224SR



























































































































































































































































































Search results

Summary of Contents for DGS-3224SR

Reviews:

Related manuals for DGS-3224SR

Brands by name

Popular brands

D-Link DGS-3224SR, Command Line Interface Reference Manual

Search results

Summary of Contents for DGS-3224SR

Reviews:

Related manuals for DGS-3224SR

Brands by name

Popular brands