D-Link DGS-3224SR Command Line Interface Reference Manual Download Page 159 | Manualshive

Page: 159 / 282

D-Link DGS-3224SR Command Line Interface Reference Manual Download Page 159

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

159

config mirror port

tx

−

Allows the mirroring of only packets

sent by (flowing out of) the port or ports in
the port list.

both

−

Mirrors all the packets received or

sent by the port or ports in the port list.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To add the mirroring ports:

DGS-3224SR:4#config mirror port 1:6 add source ports 1:1-1:5
both
Command: config mirror port 1:6 add source ports 1:1-1:5 both

Success.

DGS-3224SR:4#

config mirror delete

Purpose

Used to delete a port mirroring
configuration|

Syntax

config mirror port <port> delete source

ports <portlist> [rx|tx|both]

Description

This command is used to delete a
previously entered port mirroring

«
...
157
158
159
160
161
...
»

Summary of Contents for DGS-3224SR



























































































































































































































































































Reviews:

No comments