manualshive.com logo in svg

D-Link DGS-3224SR, Command Line Interface Reference Manual

The D-Link DGS-3224SR is a high-performance switch designed for network professionals. Enhance your network configuration skills with the Command Line Interface Reference Manual, available for free download at manualshive.com. This comprehensive manual offers detailed instructions to optimize your networking experience. Get started today and unlock the full potential of your D-Link switch.

Share
Download
background image

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide 

208

config 802.1x auth_protocol 

this command. 

 

Example Usage: 

To configure 802.1x authentication protocol: 

DGS-3224SR:4#config 802.1x auth_protocol local 
Command: config 802.1x auth_protocol local 
 
 Success. 
 
DGS-3224SR:4# 

 
 

config 802.1x capability 

Purpose 

Used to configure the 802.1x capability of a 
range of ports on the switch. 

Syntax 

config 802.1x capability ports 

[<portlist>|all] [authenticator|none] 

Description The 

config 

802.1x

 

command has two 

capabilities that can be set for each port:  
Authenticator and None. 

Parameters 

<portlist> 

−

 Specifies a range of ports. The 

portlist is specified by listing the lowest 
switch number and the beginning port 
number on that switch, separated by a 
colon. Then the highest switch number, 
and the highest port number of the range 
(also separated by a colon) are specified. 
The beginning and end of the portlist range 
are separated by a hyphen. For example, 
1:3 would specify switch number 1, port 3; 
2:4 specifies switch number 2, port 4. 

Summary of Contents for DGS-3224SR



























































































































































































































































































Reviews:

No comments

Related manuals for DGS-3224SR

Billion BiPAC 4500NZ(L) User Manual preview
BiPAC 4500NZ(L)
Brand: Billion Pages: 146
H3C s5800 series Quick Start Manual preview
s5800 series
Brand: H3C Pages: 33
H3C S5500-SI Series Operation Manual preview
S5500-SI Series
Brand: H3C Pages: 1217
3Com MSR 50 Series Configuration Manual preview
MSR 50 Series
Brand: 3Com Pages: 2443
H3C SR6600 Series Installation Manual preview
SR6600 Series
Brand: H3C Pages: 3
H3C SR6616 Installation, Quick Start preview
SR6616
Brand: H3C Pages: 4
Salto Node Installation Manual preview
Node
Brand: Salto Pages: 2
Falcon 4G COMBO User Manual preview
4G COMBO
Brand: Falcon Pages: 24
Lorex LNR100 SERIES Instruction Manual preview
LNR100 SERIES
Brand: Lorex Pages: 186
MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Brand: MiLAN Pages: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Brand: Symantec Pages: 2
Mastervolt MasterBus Tanklevel Interface User And Installation Manual preview
MasterBus Tanklevel Interface
Brand: Mastervolt Pages: 8
E-TOP PR126g User Manual preview
PR126g
Brand: E-TOP Pages: 24
Intellinet 561051 Quick Install Manual preview
561051
Brand: Intellinet Pages: 12
Ubiquiti PBE-5AC-300-ISO Quick Start Manual preview
PBE-5AC-300-ISO
Brand: Ubiquiti Pages: 28
ICP DAS USA ZT-2024 Quick Start Manual preview
ZT-2024
Brand: ICP DAS USA Pages: 8
TP-Link TD-8816 Quick Installation Manual preview
TD-8816
Brand: TP-Link Pages: 2
Hamlet HRDSL742 User Manual preview
HRDSL742
Brand: Hamlet Pages: 122

Brands by name

Popular brands

Load more brands