D-Link DGS-3224SR Command Line Interface Reference Manual Download

Page: 248 / 282

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

248

TACKING

OMMANDS

Command Parameters

config box_priority

current_box_id <value 1-12> priority
<value1-16>

config box_id

current_box_id <value1-12> new_box_id
[auto|1|2|3|4|5|6|7|8|9|10|11|12]

config box_type

current_box_id <value1-12> type [DGS-
3224SR | DES-3352SR | BOX_NOTEXIST]

config all_boxes_id

[static_mode | auto_mode]

show
stack_information

Each command is listed, in detail, in the following sections.

config box_priority

Purpose

Used to configure box priority, which
determines which box becomes master.
Lower numbers have higher priority..

Syntax

current_box_id <value 1-12> priority

<value1-16>

Description

This command configures box (switch)
priority

Summary of Contents for DGS-3224SR



























































































































































































































































































Search results

Summary of Contents for DGS-3224SR

Reviews:

Related manuals for DGS-3224SR

Brands by name

Popular brands

D-Link DGS-3224SR, Command Line Interface Reference Manual

Search results

Summary of Contents for DGS-3224SR

Reviews:

Related manuals for DGS-3224SR

Brands by name

Popular brands