D-Link DGS-3224SR Command Line Interface Reference Manual Download | Manualshive

Page: 73 / 282

background image

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

73

To delete an SNMP host entry:

DGS-3224SR:4#delete snmp host 10.52.19.2
Command: delete snmp host 10.52.19.2

Success.

DGS-3224SR:4#

show snmp host

Purpose

Used to display the recipient of SNMP traps
generated by the switch’s SNMP agent.

Syntax

show snmp host {<ipaddr>}

Description

The show snmp host

command is used to

display the IP addresses and configuration
information of remote SNMP managers that
are designated as recipients of SNMP traps
that are generated by the switch’s SNMP
agent.

Parameters

<ipaddr>

−

The IP address of a remote

SNMP manager that will receive SNMP
traps generated by the switch’s SNMP
agent.

Restrictions None.

Example Usage:

To display the currently configured SNMP hosts on the
switch:

DGS-3224SR:4#show snmp host
Command: show snmp host

«
...
71
72
73
74
75
...
»

Summary of Contents for DGS-3224SR



























































































































































































































































































Reviews:

No comments

Related manuals for DGS-3224SR

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 30

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Brand: Tyco Electronics Pages: 18

MatrixPRO-II DVI 16x16

Brand: Barco Pages: 43

Brand: Barco Pages: 5

TotalStorage SAN16M-R SAN

Brand: IBM Pages: 116

DHI-NVR2104-P-4KS2

Brand: Dahua Pages: 23

RUGGEDSWITCH RS900G

Brand: RuggedCom Pages: 23

Brand: Sangamo Pages: 2

AT-8550/SP Series

Brand: Allied Telesis Pages: 114

Brand: Belkin Pages: 57

Brand: B&B Electronics Pages: 2

Brand: Comelit Pages: 19

Brand: Solwise Pages: 7

Brand: Federal Signal Corporation Pages: 49

Brand: Perle Pages: 491

PXI PXITM -1000

Brand: National Instruments Pages: 55

Brand: KYLAND Technology Pages: 24

Brand: SMC Networks Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands