D-Link DGS-3224SR Command Line Interface Reference Manual Download

Page: 90 / 282

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

download

Purpose

Used to download and install new firmware
or a switch configuration file from a TFTP
server.

Syntax

download [ firmware <ipaddr>

<path_filename> |configuration <ipaddr>

<path_filename> {increment}]

Description

This command is used to download a new
firmware or a switch configuration file from
a TFTP server.

Parameters

firmware

−

Download and install new

firmware on the switch from a TFTP server.

configuration

−

Download a switch

configuration file from a TFTP server.

−

The IP address of the TFTP

server.

<path_filename>

−

The DOS path and

filename of the firmware or switch
configuration file on the TFTP server. For
example, C:\3224tgr.had.

unit [all|<unitid>]

−

All specifies all units

(switches), <unitid> is the unit id of the
switch that will receive the download.

increment

−

Allows the download of a

partial switch configuration file. This allows
a file to be downloaded that will change
only the switch parameters explicitly stated
in the configuration file. All other switch

Summary of Contents for DGS-3224SR



























































































































































































































































































Search results

Summary of Contents for DGS-3224SR

Reviews:

Related manuals for DGS-3224SR

Brands by name

Popular brands

D-Link DGS-3224SR, Command Line Interface Reference Manual

Search results

Summary of Contents for DGS-3224SR

Reviews:

Related manuals for DGS-3224SR

Brands by name

Popular brands