manualshive.com logo in svg

D-Link DGS-3224SR, Command Line Interface Reference Manual

The D-Link DGS-3224SR is a high-performance switch designed for network professionals. Enhance your network configuration skills with the Command Line Interface Reference Manual, available for free download at manualshive.com. This comprehensive manual offers detailed instructions to optimize your networking experience. Get started today and unlock the full potential of your D-Link switch.

Share
Download
background image

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide 

246

 

show traffic_segmentation 

Purpose 

Used to display the current traffic 
segmentation table. 

Syntax 

show traffic_segmentation 

Description 

This command will display the current 
traffic segmentation table. 

Parameters 

<portlist> - Specifies a range of ports. The 
portlist is specified by listing the lowest 
switch number and the beginning port 
number on that switch, separated by a 
colon. Then the highest switch number, 
and the highest port number of the range 
(also separated by a colon) are specified. 
The beginning and end of the portlist range 
are separated by a hyphen. For example, 
1:3 would specify switch number 1, port 3; 
2:4 specifies switch number 2, port 4. 
Thus, 1:3-2:4 specifies all of the ports 
between switch 1, port 3 and switch 2, port 
4, in numerical order. 

Restrictions none. 

 

Usage Example: 

 

To display the traffic segmentation table: 

DGS-3224SR:4#show traffic_segmentation 1-3 
Command: show traffic_segmentation 1:1-1:3 
 
Traffic Segmentation Table 

Summary of Contents for DGS-3224SR



























































































































































































































































































Reviews:

No comments

Related manuals for DGS-3224SR

OCCITALINA OXTOPUS EIA-709 User Manual preview
OXTOPUS EIA-709
Brand: OCCITALINA Pages: 54
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Brand: HARTING Pages: 13
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Xinje VH5 Series User Manual preview
VH5 Series
Brand: Xinje Pages: 76
Juniper WX 100 Quick Start Manual preview
WX 100
Brand: Juniper Pages: 6
ST STM32L4P5AG User Manual preview
STM32L4P5AG
Brand: ST Pages: 37
Variscite VAR-SOM-MX6 HEAT PLATE KIT Quick Start Manual preview
VAR-SOM-MX6 HEAT PLATE KIT
Brand: Variscite Pages: 3
Allied Telesis AR100 series User Manual preview
AR100 series
Brand: Allied Telesis Pages: 128
IBM IBM 2212-40H Installation And Initial Configuration Manual preview
IBM 2212-40H
Brand: IBM Pages: 90
LevelOne GNC-0112 Quick Installation Manual preview
GNC-0112
Brand: LevelOne Pages: 10
Devolo Kurulum Manual preview
Kurulum
Brand: Devolo Pages: 24
Zapp Z030 User Manual preview
Z030
Brand: Zapp Pages: 24
Quamtum HotSpot HS2 User Manual preview
HotSpot HS2
Brand: Quamtum Pages: 42
Digi TransPort WR41 Quick Start Manual preview
TransPort WR41
Brand: Digi Pages: 2
Kraun KN.2R User Manual preview
KN.2R
Brand: Kraun Pages: 88
Tripp Lite N306-006 Specification Sheet preview
N306-006
Brand: Tripp Lite Pages: 2
Accton Technology Edge-Core VR-200 User Manual preview
Edge-Core VR-200
Brand: Accton Technology Pages: 125
Digi TransPort WR54 Hardware Reference Manual preview
TransPort WR54
Brand: Digi Pages: 33

Brands by name

Popular brands

Load more brands