D-Link DGS-3224SR Command Line Interface Reference Manual Download

Page: 218 / 282

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

218

config radius

key

−

Specifies that a password and

encryption key will be used between the
switch and the Radius server.

−

The shared-secret key

used by the Radius server and the
switch. Up to 32 characters can be used.

default

−

Returns all of the ports in the

range to their default Radius settings.
auth_port <udp_port_number>

−

The UDP

port number for authentication requests.
The default is 1812.
acct_port <udp_port_number>

−

The UDP

port number for accounting requests. The
default is 1813.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To configure Radius settings:

DGS-3224SR:4#config radius add 1 10.48.74.121 key dlink default
Command: config radius add 1 10.48.74.121 key dlink default

Success.

DGS-3224SR:4#

show radius

Purpose

Used to display the current Radius
configurations on the switch

Summary of Contents for DGS-3224SR



























































































































































































































































































Search results

Summary of Contents for DGS-3224SR

Reviews:

Related manuals for DGS-3224SR

Brands by name

Popular brands

D-Link DGS-3224SR, Command Line Interface Reference Manual

Search results

Summary of Contents for DGS-3224SR

Reviews:

Related manuals for DGS-3224SR

Brands by name

Popular brands