D-Link DGS-3224SR Command Line Interface Reference Manual Download | Manualshive

Page: 112 / 282

background image

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

112

config stp ports

Purpose

Used to setup STP on the port level.

Syntax

config stp ports <portlist> {cost [auto

|<value1-20000000>|priority <value0-

240>|migrate [yes | no] | edge [true |

false] | p2p [true | false | auto] | state

[enable|disable]}(1)

Description

This command is used to create and
configure STP for a group of ports.

Parameters

<portlist>

−

specifies a range of ports to be

configured. The port list is specified by
listing the beginning port number and the
highest port number of the range.

The DGS3224SR is a stackable switch and
each port is designated as belonging to a
particular switch in the stack. For example,
port 2 in switch 5 in a stack is listed as 2-
5. A range of ports would be shown as 2-5,
3-6 (port 3 in switch 6), with the beginning
and the end of the range of switches
separated by a comma.

state [enable|disable]

−

Allows STP to be

enabled or disabled for the ports specified
in the port list. The default is disabled.

cost <value>

−

This defines a metric that

indicates the relative cost of forwarding
packets to the specified port list. The
default cost for a 1000 Mbps port is
20,000, a 100 Mbps port is 200,000, and
for a 10 Mbps port the default cost is

«
...
110
111
112
113
114
...
»

Summary of Contents for DGS-3224SR



























































































































































































































































































Reviews:

No comments

Related manuals for DGS-3224SR

Brand: D-Link Pages: 12

Brand: Panasonic Pages: 44

Brand: Abocom Pages: 11

Brand: Abocom Pages: 19

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Brand: Zonet Pages: 8

Brand: SyChip Pages: 24

Brand: ProCurve Pages: 2

Brand: ADTRAN Pages: 2

Brand: Tripp Lite Pages: 2

Brand: Westlock Controls Corporation Pages: 39

Brand: HALNy Pages: 12

Brand: Crestron Pages: 52

Brand: Honeywell Pages: 20

Brand: Honeywell Pages: 8

Brand: Honeywell Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands