D-Link DES-3010F Command Line Interface Manual Download Page 71 | Manualshive

Page: 71 / 187

background image

DES-3000 Series Layer 2 Switch CLI Reference Manual

DES-3026:4#config stp ports 1-5 cost 19 priority 15 state enabled
Command: config stp ports 1-5 cost 19 priority 15 state enabled

Success.

DES-3026:4#

enable stp

Purpose

Used to globally enable STP on the Switch.

Syntax

enable stp

Description

This command allows the Spanning Tree Protocol to be globally
enabled on the Switch.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To enable STP, globally, on the Switch:

DES-3026:4#enable stp
Command: enable stp

Success.

DES-3026:4#

disable stp

Purpose

Used to globally disable STP on the Switch.

Syntax

disable stp

Description

This command allows the Spanning Tree Protocol to be globally
disabled on the Switch.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To disable STP on the Switch:

DES-3026:4#disable stp
Command: disable stp

Success.

DES-3026:4#

show stp

Purpose

Used to display the Switch’s current STP configuration.

Syntax

show stp

Description

This command displays the Switch’s current STP configuration.

Parameters None.

69

«
...
69
70
71
72
73
...
»

Summary of Contents for DES-3010F




























































































































































































Reviews:

No comments

Related manuals for DES-3010F

Transportation FiberinMotion

Brand: Radwin Pages: 122

Brand: Ubee Pages: 9

Brand: Google Pages: 14

DM/IP601-CPCI-100BT

Brand: Dialogic Pages: 2

Brand: Idis Pages: 85

Brand: Razer Pages: 17

Brand: Topcom Pages: 16

Brand: FiberHome Pages: 2

HomePNA PCI Adapter

Brand: City-Netek Pages: 18

ACC-BKT-AX-BEAM

Brand: Extreme Networks Pages: 35

Brand: TRENDnet Pages: 2

Brand: Juniper Pages: 30

Brand: Geneko Pages: 8

Brand: Echelon Pages: 99

Brand: Linksys Pages: 37

Brand: C-Data Pages: 19

Brand: Billion Pages: 2

SteelCentral AppResponse 2170

Brand: Riverbed Pages: 166

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands