manualshive.com logo in svg

D-Link DES-3010F, Command Line Interface Manual

Share
Download
D-Link DES-3010F Command Line Interface Manual Download Page 148

DES-3000 Series Layer 2 Switch CLI Reference Manual

 

show 802.1x

 

auth_configuration 

/ForceAuth/ForceUnauth 

−

 Shows the current state of the Authenticator PAE. 

Backend State: Request/Response/Fail/Idle/Initialize 

−

 Shows the current state of the 

Backend Authenticator. 

ReAuthenticate: Enabled/Disabled 

−

 Shows whether or not to re-authenticate. 

AdminCtlDir: Both/In 

−

 Shows whether a controlled Port that is unauthorized will exert control 

over communication in both receiving and transmitting directions, or just the receiving 
direction. 

OpenCtlDir: Both/In 

−

 Shows whether a controlled Port that is unauthorized will exert control 

over communication in both receiving and transmitting directions, or just the receiving 
direction. 

Port Control: ForceAuth/ForceUnauth/Auto 

−

 Shows the administrative control over the port’s 

authorization status. ForceAuth forces the Authenticator of the port to become Authorized. 
ForceUnauth forces the port to become Unauthorized. 

QuietPeriod 

−

 Shows the time interval between authentication failure and the start of a new 

authentication attempt. 

TxPeriod 

−

 Shows the time to wait for a response from a supplicant (user) to send EAP 

Request/Identity packets. 

SuppTimeout 

−

 Shows the time to wait for a response from a supplicant (user) for all EAP 

packets, except for the Request/Identity packets. 

ServerTimeout 

−

 Shows the length of time to wait for a response from a RADIUS server. 

MaxReq 

−

 Shows the maximum number of times to retry sending packets to the supplicant. 

ReAuthPeriod 

−

 Shows the time interval between successive re-authentications. 

Parameters 

ports <portlist> 

−

 Specifies a port or range of ports to be viewed.  

Restrictions Only 

administrator-level users can issue this command. 

Example usage: 

To display the 802.1x configurations:  

DES-3026:4#show 802.1x auth_configuration ports 1 
Command: show 802.1x auth_configuration ports 1 
 
802.1X                               : Enabled 
Authentication Mode       : Port_based 
Authentication Protocol  : Radius_Eap 
Port number     : 1     
Capability      : None          
AdminCrlDir     : Both 
OpenCrlDir      : Both 
Port Control    : Auto               
QuietPeriod     : 60    sec 
TxPeriod        : 30    sec 
SuppTimeout     : 30    sec 
ServerTimeout   : 30    sec 
MaxReq          : 2     times 
ReAuthPeriod    : 3600  sec 
ReAuthenticate  : Disabled 

 

 

 

 

 

146

Summary of Contents for DES-3010F




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands