manualshive.com logo in svg

D-Link DES-3010F, Command Line Interface Manual

Share
Download
D-Link DES-3010F Command Line Interface Manual Download Page 145

DES-3000 Series Layer 2 Switch CLI Reference Manual

 

Each command is listed, in detail, in the following sections. 

 

NOTE:

 The uplink module ports (DES-3010F/FL/G ports 9-10, DES-3018 

ports 17-18, DES-3026 ports 25-26) do not support the 802.1X function. 

 

enable 802.1x 

Purpose 

Used to enable the 802.1x server on the Switch. 

Syntax 

enable 802.1x 

Description 

The 

enable 802.1x 

command enables the 802.1x Port-based or MAC-

based Network Access control server application on the Switch. 

Parameters None. 

Restrictions Only 

administrator-level users can issue this command. 

Example usage: 

To enable 802.1x switch wide:

 

DES-3026:4#enable 802.1x 
Command: enable 802.1x 
 
Success. 
 
DES-3026:4# 

 

disable 802.1x 

Purpose 

Used to disable the 802.1x server on the Switch. 

Syntax 

disable 802.1x 

Description 

The 

disable 802.1x 

command is used to disable the 802.1x Port-based or 

MAC-based Network Access control server application on the Switch. 

Parameters None. 

Restrictions Only 

administrator-level users can issue this command. 

Example usage: 

To disable 802.1x on the Switch: 

DES-3026:4#disable 802.1x 
Command: disable 802.1x 
 
Success. 
 
DES-3026:4# 

 

 

 

 

143

Summary of Contents for DES-3010F




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands