Cradlepoint COR IBR350 Page 6 Manual Download | Manualshive

Page: 6 / 148

background image

• Directional Yagi (Log-Periodic) antennas for external (outside) mounting (Part # 170588-000)
• Omni-directional antennas for external (outside) mounting (Part # 170586-000)
• 12” Mag-mount antenna (Part # 170605-000)
• 4” Mini mag-mount antenna (Part # 170606-000)

See the Cradlepoint

antenna accessories page

for more information about antennas. Also see the

AntennaOrderingandInstallationGuide

,

available as a PDF in the

Resources

section of antenna and router product pages.

Business-GradeModemSpeciﬁcations

COR IBR350 models include an integrated 4G LTE modem – speciﬁc model names include a speciﬁc modem (e.g., the COR IBR350L-VZ includes
a Verizon LTE modem).

COR IBR350L-VZ –4G LTE forVerizon

•

Technology

: LTE

•

DownlinkRates

: LTE 100 Mbps (theoretical)

•

UplinkRates

: LTE 50 Mbps (theoretical)

•

FrequencyBands

:

–

LTE Band 4 – AWS (1700/2100 MHz), Band 13 (700 MHz)

•

Power

: LTE 23 dBm +/− 1 (typical conducted)

•

Antennas

: two SMA male (plug), ﬁnger tighten only (maximum torque spec is 7 kgf-cm)

•

IndustryStandards&Certs

: FCC, Verizon

Hardware

Ports&LEDs

ANTENNA CONNECTORS

– There are two antenna connectors for the integrated 3G/4G modem (SMA). The

MAIN

modem connector may have

better performance than the

AUX

connector, so attach the better (or single) modem antenna to the MAIN connector if that is relevant in your setup.

POWER SWITCH

– The device must be powered oﬀ to insert/remove the SIM. I – on &pipe; O – oﬀ

MICRO-B USB

– This is a service port for

modem ﬁrmware updates ONLY.

RESET

– Press and hold for ten seconds to factory reset the device.

ETHERNET LAN/PORT

– An Ethernet cable

is required to connect to the device. By default the Ethernet port is set to LAN, and is not LAN/WAN conﬁgurable.

LEDs

–

POWER

• Green = Powered ON.

6

«
...
4
5
6
7
8
...
»

Summary of Contents for COR IBR350





















































































































































Reviews:

No comments

Related manuals for COR IBR350

OFFICESERV 7100

Brand: Samsung Pages: 97

NMEA CONNECT PLUS

Brand: Calypso Instruments Pages: 26

Brand: Actiontec Electronics Pages: 6

Brand: Gefen Pages: 13

Brand: Artila Pages: 22

AirLink GX Series

Brand: Sierra Wireless Pages: 2

Projector Gateway

Brand: Acer Pages: 58

Brand: Cisco Pages: 10

Brand: Cisco Pages: 7

Brand: Cisco Pages: 19

Network Device MGX 8240

Brand: Cisco Pages: 2

Physical Access CIAC-GW-K9

Brand: Cisco Pages: 26

Brand: Cisco Pages: 60

Brand: Cisco Pages: 58

Brand: Cisco Pages: 29

Brand: Cisco Pages: 94

Brand: Cisco Pages: 5

Brand: Cisco Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands