Cradlepoint COR IBR350 Page 84 Manual Download | Manualshive

Page: 84 / 148

background image

Figure 108: IPv6 Conﬁguration Example

•

AdditionalIPv6DNS Server

– Secondary DNS server.

•

DelegatedIPv6Network

– (optional) Network available for delegation to LANs. Depending on your provider, this may be required. Preﬁxes

speciﬁed here only take eﬀect if those supplied by the connection are insuﬃcient to conﬁgure your LANs.

•

DelegatedIPv6Network

– Additional network available for delegation to LANs.

Example Conﬁguration:

##### 6to4 Tunnel

Out of the box, 6to4 is the simplest mode to enable full end-to-end IPv6 connectivity in an organization if the upstream ISP properly routes packets
to and from the 6to4 unicast relay servers.

•

PrimaryIPv6DNS Server

– (optional) Depending on your provider, this may be required. This only takes eﬀect if the default global DNS

setting on the

NetworkSettings>DNS

page is “Automatic”.

•

AdditionalIPv6DNS Server

– Secondary DNS server.

•

DelegatedIPv6Network

– (optional) Network available for delegation to LANs. Depending on your provider, this may be required. Preﬁxes

speciﬁed here only take eﬀect if those supplied by the connection are insuﬃcient to conﬁgure your LANs.

•

DelegatedIPv6Network

– Additional network available for delegation to LANs.

Example Conﬁguration:

Figure 109: IPv6 Example Conﬁguration

The 6in4 tunnel mode utilizes explicit IPv4 tunnel endpoints and encapsulates IPv6 packets using 41 as the speciﬁed protocol type in the IP header.
A 6in4 tunnel broker provides a static IPv4 server endpoint, decapsulates packets, and provides routing for both egress and ingress IPv6 packets.
Most tunnel brokers provide a facility to request delegated networks for use through the tunnel.

84

«
...
82
83
84
85
86
...
»

Summary of Contents for COR IBR350





















































































































































Reviews:

No comments

Related manuals for COR IBR350

MultiVOIP MVP210-SS

Brand: Multitech Pages: 36

Brand: Symantec Pages: 2

Brand: UfiSpace Pages: 14

Brand: New Rock Technologies Pages: 75

Brand: Badger Meter Pages: 24

Mediant 500Li MSBR

Brand: AudioCodes Pages: 10

ZyWALL USG 2000

Brand: ZyXEL Communications Pages: 120

Brand: Encom Pages: 33

Brand: Burkert Pages: 13

POW-R-COMMAND 1000

Brand: Eaton Pages: 8

Brand: 2Wire Pages: 82

Brand: David Clark Pages: 11

Brand: David Clark Pages: 13

Brand: Clearswift Pages: 21

Optinet FE408005AA

Brand: Black Box Pages: 159

Brand: Celestix Pages: 37

Brand: PiiGAB Pages: 68

Brand: Avaya Pages: 254

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands