Cradlepoint COR IBR350 Page 100 Manual Download | Manualshive

Page: 100 / 148

background image

GRE Tunnels

Generic Routing Encapsulation (GRE) tunnels can be used to create a connection between two private networks. Most Cradlepoint routers are
enabled for both GRE and VPN tunnels. GRE tunnels are simpler to conﬁgure and more ﬂexible for diﬀerent kinds of packet exchanges, but VPN
tunnels are much more secure.

Figure 129: GRE Tunnels

In order to set up a tunnel you must conﬁgure the following:

•

LocalNetwork

and

RemoteNetwork

addresses for the “

GlueNetwork

,” the network that is created by the administrator that serves as

the “glue” between the networks of the tunnel. Each address must be a diﬀerent IP address from the same private network, and these
addresses together form the endpoints of the tunnel.

•

RemoteGateway

, the public facing WAN IP address that the local gateway is going to connect to.

•

Routes

that allow you to conﬁgure what network traﬃc from local host(s) will be allowed through the tunnel.

• Optionally, you might also want to enable the tunnel

KeepAlive

feature to monitor the status of a tunnel and more accurately determine if

the tunnel is alive or not.

Optionally, you might also want to enable the tunnel

KeepAlive

feature to monitor the status of a tunnel and more accurately determine if the

tunnel is alive or not.

Click

Add

to conﬁgure a new GRE tunnel; click

Edit

to make changes to an existing tunnel.

Add/EditTunnel–General TunnelName

: Give the tunnel a name that uniquely identiﬁes it.

TunnelKey

: Enables an ID key for a GRE tunnel, which can be used as an identiﬁer for mGRE (Multipoint GRE).

LocalNetwork

: This is the local side of the “Glue Network,” a network created by the administrator to form the tunnel. The user creates the IP

address inputted here. It must be diﬀerent from the IP addresses of the networks it is gluing together. Choose any private IP address from the
following three ranges that doesn’t match either network:

• 10.0.0.0 - 10.255.255.255
• 172.16.0.0 - 172.31.255.255
• 192.168.0.0 - 192.168.255.255

RemoteNetwork

: This is the remote side of the “Glue Network.” Again, the user must create an IP address that is distinct from the IP addresses

of the networks that are being glued together. The Remote Network and Local Network values will be ﬂipped when inputted for the other side of
the tunnel conﬁguration.

SubnetMask

: This is the subnet mask for the Glue Network. The Local and Remote Network addresses must ﬁt with this mask. 255.255.255.0 is

a logical choice for most users.

RemoteGateway

: This is the public facing, WAN-side IP address of the network that the local gateway is going to connect to.

100

«
...
98
99
100
101
102
...
»

Summary of Contents for COR IBR350





















































































































































Reviews:

No comments

Related manuals for COR IBR350

Brand: XiNCOM Pages: 82

460R - Gateway Security

Brand: Symantec Pages: 54

Brand: DCB Pages: 64

NETcon D-G-64NE

Brand: ZIEHL-ABEGG Pages: 27

Brand: Ascent Communication Technology Pages: 114

Brand: BEC Pages: 14

Brand: Kunbus Pages: 30

CONTROLS Series

Brand: Condair Pages: 16

Brand: Huawei Pages: 28

Brand: Sony Pages: 70

Brand: Sony Pages: 76

Brand: ETC Pages: 5

Brand: Authonet Pages: 2

Brand: San Telequip Pages: 19

Brand: ActionTec Pages: 41

Brand: enphase Pages: 3

Brand: enphase Pages: 6

ENV-S-AM1-230-60

Brand: enphase Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands