Cormach MEC 810VD-VDL-VDBL, Use And Maintenance Manual

Page: 72 / 78

Use and Maintenance Manual – 08/2018 Rel. 3 Page 67
22. ERROR CODES AND SOLUTION
The Error signal is always accompanied by a triple beep indicating that the machine cannot run the command given by the operator,
or, during operation, conditions were encountered that prevent the action in progress from continuing. The machine reports error
conditions by displaying an outline of the description of the cause of the error. The list of error codes and description outlines is
provided in table T22.1.
Table T22.1: Error codes
INTERNAL ERRORS
Code Description Notes
000 to 020 Machine parameters internal error. Contact technical support.
099 CPU internal error. Turn the machine off and then on again. If the error persists, contact
technical support.
G00 Communication failure between graphics card
and CPU.
Turn the machine off and then on again. If the error persists, contact
technical support.
SENSOR ERRORS
Code Description Notes
016 Distance sensor is not in rest position at start-up
of the machine or when [P8] Start is pressed.
Place the sensor back in its rest position: the error should disappear. If
the error persists, contact technical support.
NOTE: if key [P5] is pressed the machine acquisition system is
temporarily disabled and operation can be continued. The disabled
status will last until the machine has been turned off.
017 Width sensor is not in rest position at start-up of
the machine or when Start key [P8] is pressed.
Place the sensor back in its rest position: the error should disappear. If
the error persists, contact technical support.
NOTE: if key [P5] is pressed the machine acquisition system is
temporarily disabled and operation can be continued. The disabled
status will last until the machine has been turned off.
046 The Diameter sensor is enabled but
disconnected.
Press key [P5]: the machine acquisition system is temporarily disabled
and operation can be continued. The disabled status will last until the
machine has been turned off.
047 The Width sensor is enabled but disconnected. Press key [P5]: the machine acquisition system is temporarily disabled
and operation can be continued. The disabled status will last until the
machine has been turned off.
CALIBRATION ERRORS
Code Description Notes
021 – 030 – 031 Lack of machine calibration data or incorrect
calibration data.
Carry out calibration for the CAR/SUV Wheel Type and/or for the MOTO
Wheel Type. If the error persists, contact technical support.
022 to 024 Error during calibration. Excessive imbalance or anomaly. Turn the machine off and then on
again. If the error persists, contact technical support.
025 Presence of weight during the Cal0 calibration
phase.
Remove the weight and repeat the launch of the Cal0 phase. If the error
persists, contact technical support.
026 A launch without weight or failure of the pick-up
A signal in the Cal2 calibration phase.
Apply the intended weight and repeat the launch. If the error persists,
contact technical support.
027 A launch without weight or failure of the pick-up
B signal in the Cal2 calibration phase.
Apply the intended weight and repeat the launch. If the error persists,
contact technical support.
028 Launch with weight on the internal side during
the Cal3 calibration phase. In this phase, the
weight must be on the external side.
Remove the weight from the internal side and repeat the launch. If the
error persists, contact technical support.
034 The MOTO Wheel Type: it is not possible to use a
Program Type other than ALU1.
Other Program Types cannot be selected.
043 The flange for motorbikes was not exactly vertical
when [P8] Start was pressed during the MOTO
Cal2 and Cal3 calibration phases.
Put the flange for motorbikes exactly vertical (and with the CAL
reference on the upper part) then press [P8] Start.
GENERIC ERRORS
Code Description Notes
039 The wheel guard is open: it is not possible to
perform the requested action.
051 – 052 Hidden Weights program: the selected point is
too far from the external imbalance position.
Hidden Weights program: the external imbalance
position is not between the selected W1 and W2
points.
The point must be included up to 120° from the external imbalance
position. See chapter 18.
Choose W1 and W2 points so that they include the external imbalance
position. See chapter 18.
055 The static imbalance of the wheel is too low: it is
not possible to use the Optimization program.
NOTE: For the error codes that are not reported in table T22.1, CONTACT THE TECHNICAL SERVICE.