3DB
1-3-29
Maintenance
Description
item No.
U660
Setting the system (communication 2)
Description
Makes settings for fax transmission regarding the communication.
Purpose
To reduce transmission errors when a low quality line is used.
Start
1. Press the start key. The screen for selecting an item is displayed.
2. Press the appropriate item.
The screen for the selected item appears.
Sets the criteria for receiving a TCF signal 2.
Sets the short protocol transmission.
Sets the reception of short protocol transmission.
Sets the CNG detection times in the fax/telephone auto select mode.
Turns ECM for one-touch dialing on/off.
Display
TCF CHECK 2
SHORT PROTOCOL TX
SHORT PROTOCOL RX
NUMBER of CNG (F/T)
1TOUCH ECM
Description
Setting the criteria for receiving a TCF signal 2
Sets the signal checking time as a criterion for a received TCF signal.
1. Enter 1 or 2 using the numeric key to change the setting.
Checks for 1.0 s.
Checks for 0.8 s.
Display
1: LONG
2: SHORT
Description
2. Press the start key. The value is set.
3. To return to the screen for selecting an item, press the stop/clear key.
Setting the short protocol transmission
Sets if short protocol transmission is performed.
1. Change the setting using the numeric keys.
Short protocol transmission is performed.
Short protocol transmission is not performed.
Display
1: ON
2: OFF
Description
2. Press the start key. The value is set.
3. To return to the screen for selecting an item, press the stop/clear key.
Setting the reception of a short protocol transmission
Selects whether to receive or ignore transmission using short protocol.
If a short protocol transmission is received when an auto switching device is attached to the machine,
communication problems, including auto switching inability, sometimes occur. Change the setting to ignore
short protocol transmission to prevent such problems.
1. Change the setting using the numeric keys.
Receives short protocol transmission.
Ignores short protocol transmission.
Display
1: ON
2: OFF
Description
2. Press the start key. The value is set.
3. To return to the screen for selecting an item, press the stop/clear key.
Summary of Contents for Ri 2530
