1-3-2
3CM
Section
Item
Maintenance item contents
Initial
No.
setting
Fax
U610 Setting the modem output level
• Setting the modem output level
—
• Adjusting the modem output level
—
U611 G3 cable equalizer
• Setting the G3 transmission cable equalizer
—
• Setting the G3 reception cable equalizer
—
U612 Setting the modem detection level
—
U613 Setting the DTMF output level
• Setting the DTMF (high-frequency group) output level
—
• Setting the DTMF (low-frequency group) output level
—
U614 Adjusting the DTMF output level
• Adjusting the DTMF (high-frequency group) output level
—
• Adjusting the DTMF (low-frequency group) output level
—
U615 Setting the NCU
• Setting the connection to PBX/PSTN
—
• Setting PSTN dial tone detection
—
• Setting busy tone detection
—
• Setting for a PBX
—
U616 Adjusting the ratio of make-to-break of dial pulses
• Make time (10 PPS)
—
• Make time (20 PPS)
—
U617 Outputting lists
• Settings list
—
• Action list
—
• Monitor list
—
• Own-status report
—
• Protocol list
—
• One-touch dialing ECM setting list
—
U650 Setting the system 1
• Setting the number of lines to be ignored when receiving a fax
at 100% magnification
3
• Setting the number of lines to be ignored when receiving a fax
in the auto reduction mode
3
• Setting the number of lines to be ignored when receiving a fax (A4R, letter)
in the auto reduction mode
3
• Setting the recording width for inch specifications
—
• Setting automatic printing of the protocol list
—
U651 Setting the system 2
• Setting the variation range in the auxiliary scanning direction
for rotation reception
3
• Setting the number of adjustment lines for automatic reduction
7
• Setting the number of adjustment lines for automatic reduction
when A4 paper is set
22
• Setting the number of adjustment lines for automatic reduction
when letter size paper is set
26
U660 Setting the system (communication 2)
• Setting the criteria for receiving a TCF signal 2
—
• Setting the short protocol transmission
—
• Setting the reception of a short protocol transmission
—
• Setting the CNG detection times in the fax/ telephone auto select mode
—
• Turning ECM for one-touch dialing on/off
—
U670 Setting the system (communication 3)
• Setting if V.34 transmission is available
—
• Setting the V.34 symbol speed (3429 Hz)
—
• Setting the V.34 symbol speed (3200 Hz)
—
• Setting the V.34 symbol speed (3000 Hz)
—
• Setting the V.34 symbol speed (2800 Hz)
—
U680 Displaying the fax board ROM version
—
Summary of Contents for Ri 2530
