background image

50

Maintenance

2583701_C_EN_1812_Nortec-GS_OM

Nortec GS

Maintenance

6.1 

General

To ensure proper performance and long operating life of the Nortec GS humidifier, Condair recommends 

inspection of the appliance and installation at least once a year by a qualified service person. The amount 

and type of maintenance required is generally dependent on how much the humidifier operates. The 

Nortec GS humidifier monitors the amount of steam produced over time and will indicate when service 

is required. All units come with a default service interval of 1000 hours, which can be adjusted in the 

control software.
The combustion air blower motors are permanently lubricated and do not require lubrication.
The gas valves in the Nortec GS humidifier are negative static pressure regulating valves. The valves are 

factory-set for the correct gas type. The valve setting listed on the product rating plate is shown relative 

to atmosphere – this setting will always remain constant. Contact the factory if adjustment is needed.

IMPORTANT!

 Tampering with the gas valve, without the express consent of Condair, will void the 

warranty.

In general, the burners do not require adjustment or servicing. The combustion chamber and heat-

exchanger tubes are all fabricated from stainless steel, and do not require internal cleaning.
The exhaust vent connected to the Nortec GS humidifier does not require cleaning, but needs to be 

inspected regularly for leaks, blockages, sagging and proper condensate removal. 
For proper and safe operation of the unit, the area around the air intake in the unit must be kept clear of 

all obstructions. If an air intake vent is used, it must be inspected for leaks and obstructions (including 

the intake terminal).

Refer to 

"Mandatory Maintenance Schedule" on page 51

 for other maintenance requirements. Also perform 

regular inspections when the unit is operating – refer to 

"Inspections During Operation" on page 46

.

IMPORTANT!

 Damage caused by use of non-approved parts is not covered by warranty. Use only 

original Condair replacement parts.

Personnel Qualifications

Maintenance on the Nortec GS humidifier must only be performed by well qualified and properly trained 

personnel authorized by the customer. It is the customer's responsibility to verify qualifications of the 

personnel.

Safety

Make sure that the Nortec GS humidifier is shut down properly as described in 

"Shutting Down" on page 48

and observe all safety precautions described in 

"For Your Safety"

 before performing any maintenance on 

the humidifier.

WARNING!

Wiring errors can cause improper and dangerous operation of the humidifier!

Prevention:

 Tag all wires before disconnecting them. Reconnect all wires correctly after servicing, 

and check the unit functions properly.

 

Summary of Contents for Nortec GS 50





























































































Reviews: