Comtrend Corporation CT-5624S User Manual Download Page 78 | Manualshive

Page: 78 / 90

background image

9.6.1 Services

The Services option limits or opens the access services over the LAN or WAN.
These services are provided FTP, HTTP, ICMP, SNMP, SSH (Security Socket Share),
TELNET, and TFTP. The “Services” can be enabled for LAN side, WAN side, or
both. Enable the service by checking the item in the corresponding checkbox, and
then click

Save/Apply

.

- -

77

«
...
76
77
78
79
80
...
»

Summary of Contents for CT-5624S



























































































Reviews:

No comments

Related manuals for CT-5624S

AirPlus DWL-810

Brand: D-Link Pages: 25

Brand: H3C Pages: 6

OfficeConnect 3CP4144

Brand: 3Com Pages: 4

OfficeConnect 3CP4144

Brand: 3Com Pages: 2

Brand: H3C Pages: 60

Brand: H3C Pages: 149

Brand: 3Com Pages: 27

OfficeConnect 3C19500

Brand: 3Com Pages: 52

Brand: D-Link Pages: 83

Hollywood DV-Bridge

Brand: Dazzle Pages: 63

Brand: Lancom Pages: 70

Brand: Patton electronics Pages: 12

Brand: Kaptia Pages: 14

DataPlot CB1224

Brand: B-G Instruments Pages: 4

Brand: iNetVu Pages: 20

Brand: ZyXEL Communications Pages: 66

Brand: ATTO Technology Pages: 2

Brand: DayTronic Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands