Comtrend Corporation CT-5624S User Manual Download Page 56 | Manualshive

Page: 56 / 90

background image

7.6 Routing

The Routing dialog box allows you to configure Default gateway and Static Route.

7.6.1 Default

Gateway

If ‘

Enable Automatic Assigned Default Gateway’

checkbox is selected, this

router will accept the first received default gateway assignment from one of the
PPPoA, PPPoE or MER/DHCP enabled PVC(s). If the checkbox is not selected, enter
the static default gateway AND/OR a WAN interface. Click ‘Save/Apply’ button to
save it.

NOTE:

If changing the Automatic Assigned Default Gateway from unselected to

selected, You must reboot the router to get the automatic assigned
default gateway.

- -

55

«
...
54
55
56
57
58
...
»

Summary of Contents for CT-5624S



























































































Reviews:

No comments

Related manuals for CT-5624S

Brand: Paradyne Pages: 85

DM/IP601-CPCI-100BT

Brand: Dialogic Pages: 2

Brand: Lancom Pages: 70

Brand: Patton electronics Pages: 12

Brand: TP-Link Pages: 110

HiGain H2TU-R-402 List 7A

Brand: ADC Pages: 7

Brand: Renesas Pages: 28

Brand: Moxa Technologies Pages: 51

Brand: NC-link Pages: 20

Brand: Moxa Technologies Pages: 36

Brand: Idis Pages: 17

IGS-5225-20T4C2X

Brand: Planet Pages: 16

Brand: Tripp Lite Pages: 34

ReadyNAS 3220 Series

Brand: NETGEAR Pages: 4

24-Port 1000BASE-T

Brand: Comet Labs Pages: 44

Brand: TRENDnet Pages: 57

Brand: ENKHO Pages: 48

Brand: Foxconn Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands