Comtrend Corporation CT-5624S User Manual Download Page 36 | Manualshive

Page: 36 / 90

background image

Note: Enable DHCP Server Relay

will not display if Firewall is enabled in the

previous step.

7. Click

Next

to display the following screen.

8. After clicking

Save/Reboot

, the router will save the configuration to the flash

memory, and reboot.    The Web UI will not respond until the system is brought up
again.    After the system is up, the Web UI will refresh to the Device Info page
automatically.    The CT-5624S is ready for operation and the LEDs display as
described in the LED description tables.

- -

35

«
...
34
35
36
37
38
...
»

Summary of Contents for CT-5624S



























































































Reviews:

No comments

Related manuals for CT-5624S

Brand: Habitat Pages: 48

TokenLink Velocity 3C319

Brand: 3Com Pages: 2

COMSPHERE 3800 Series

Brand: Paradyne Pages: 88

COMSPHERE 3800PLUS

Brand: Paradyne Pages: 5

Brand: Paradyne Pages: 2

Brand: LaCie Pages: 22

RIPWAVE 40-00460-00R

Brand: Navini Networks Pages: 35

Brand: Maipu Pages: 19

iMarc SLV 9820-2M

Brand: Paradyne Pages: 24

Brand: NETGEAR Pages: 152

Brand: Avigilon Pages: 12

Brand: Dantel Pages: 22

Brand: Net Optics Pages: 2

SteelCentral NetExpress 470

Brand: Riverbed Pages: 140

Brand: Gbord Pages: 11

Brand: Me Pages: 28

Brand: Caimore Pages: 79

SWC-2100 (VoIP CPE)

Brand: SEOWON INTECH Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands