Comtrend Corporation CT-5624S User Manual Download Page 17

Page: 17 / 90

In Errors

Number of received AAL5/AAL0 CPCS PDUs received that
contain an error. The types of errors counted include CRC-32
errors.

Out Errors

Number of received AAL5/AAL0 CPCS PDUs that could be
transmitted due to errors.

In Discards

Number of received AAL5/AAL0 CPCS PDUs discarded due to
an input buffer overflow condition.

Out Discards

This field is not currently used

ATM AAL5 LAYER STATISTICS FOR EACH VCC OVER ADSL INTERFACE

Field Descriptions

CRC Errors

Number of PDUs received with CRC-32 errors

SAR TimeOuts

Number of partially re-assembled PDUs which were discarded
because they were not fully re-assembled within the required
period of time. If the re-assembly time is not supported
then, this object contains a zero value.

Over Sized SDUs Number of PDUs discarded because the corresponding SDU

was too large

Short Packets
Errors

Number of PDUs discarded because the PDU length was less
than the size of the AAL5 trailer

Length Errors

Number of PDUs discarded because the PDU length did not
match the length in the AAL5 trailer

- -

Summary of Contents for CT-5624S



























































































Search results

Summary of Contents for CT-5624S

Reviews:

Related manuals for CT-5624S

Brands by name

Popular brands

Comtrend Corporation CT-5624S, User Manual

Search results

Summary of Contents for CT-5624S

Reviews:

Related manuals for CT-5624S

Brands by name

Popular brands