Comtrend Corporation CT-5624S User Manual Download | Manualshive

Page: 67 / 90

background image

7.10.2 Trusted CA

CA is the abbreviation for Certificate Authority. CA is a part of the X.509 system.
It is itself a certificate, attached with the owner information of this certificate
authority; but its purpose is not to do encryption/decryption. Its purpose is to
sign and issue certificates in order to prove that the certificate is valid.

Click

Import Certificate

to paste the certificate content of your trusted CA.

Generally speaking, the certificate content will be provided by your vendor/ISP/
ITSP and is used to authenticate the Auto-Configuration Server (ACS) that the
CPE will connect to.

- -

66

«
...
65
66
67
68
69
...
»

Summary of Contents for CT-5624S



























































































Reviews:

No comments

Related manuals for CT-5624S

Brand: D-Link Pages: 14

Brand: D-Link Pages: 7

Brand: D-Link Pages: 41

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Brand: D-Link Pages: 53

Brand: Hawking Pages: 2

Brand: Edgewater Networks Pages: 7

Brand: EVOC Pages: 57

Brand: Aethra Pages: 2

Brand: Teletronics International Pages: 57

Brand: Unex Pages: 27

Brand: Hamlet Pages: 11

Brand: Idis Pages: 16

Brand: Hama Pages: 7

Brand: Supero Pages: 54

ACC-BKT-AX-BEAM

Brand: Extreme Networks Pages: 35

Brand: LevelOne Pages: 61

Brand: Network Instruments Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands