Comtech EF Data SDM-300L3 Installation And Operation Manual Download Page 24

Page: 24 / 408

SDM-300L3 Satellite Modem

Revision 1

Introduction

MN/SDM300L3.IOM

1–4

Option

Description & Comments

Availability

Install

Option

G.703 Interface. Note, For BNC or 15 pin
D interface see UB-530 breakout panels.

Requires Overhead Card with 50 pin D
Connector

Yes User

G.703/ASYNC, Closed Network only

BNC-F connectors and ASYNC.
Requires Overhead card

Yes User

37-Pin Female D Connector

EIA-422/EIA-449 Interface and
Mil-188-114

Yes User

25-Pin Female D Connector

EIA-530 (RS-422), EIA-232 and V.35

Yes

User

34-Pin Female V.35

“Winchester” Connector with V.35

Yes

User

50-Pin Female D Connector for use
Without Overhead card.

Includes EIA-422, EIA-232, and V.35
Use with redundancy switches

Yes User

IBS Interface

Requires Overhead Card

Yes

User

IDR Interface

Requires Overhead Card

Yes

User

Drop & Insert Interface

Requires Overhead Card

Yes

User

Primary Power: Auto-ranging AC 85 to 264
VAC

Yes

Factory

Primary Power: 48 VDC (Modem only, No
BUC)

Yes

Factory

ODU DC Power: 24V or 48V. Primary
input = AC Only

100W @ 24V
150W @ 48V

Yes Factory

1.3

Comtech EF Data Part Numbers

Part No.

Description

Remarks

PL/9066-3

RX only IF 1.0 ppm

Use with internal reference LNBs.
Hardware limited version.

PL/9066-2

TX only IF 0.02 ppm

Hardware limited version

PL/9066-1

TX/RX IF 0.02 ppm

Full Duplex

PL/9066-5

TX/RX IF 1.0 ppm

Full Duplex (No BUCs)

PL/5727-1 25-pin

EIA-530

Interface

PL/6031-1 37-pin

EIA-449

Interface

PL/5305-2
PL/5509-2

50-pin

Interface With Overhead

PL/6167-1

50-pin

Interface No Overhead

PL/6032-1 34-pin

Interface

V.35

PL/5305-2
PL/7838-1

G.703/ASYNC

Interface with Overhead
Closed Network

PL/6284 TX

Reed-Solomon

PL/6285 RX

Reed-Solomon

PL/9394-1 TX/RX

Turbo

PL/9658-1 Duplex

Reed-Solomon

PS/AC65W01P01

90-264 VAC Modem PS

Modem only

PS/DC-DC5V65W

-48 VDC Modem PS

Modem only

KT/9567-2

90 – 264 VAC, 100W
BUC P/S, 24V, CE Mark

24 VDC, 100W
AC BUC Power Supply

KT/9567-3

90 – 264 VAC, 150 W
BUC P/S, 48 VDC

48 VDC 150 W
AC BUC Power Supply

Summary of Contents for SDM-300L3

























































































































































































































































































































































































































Search results

Summary of Contents for SDM-300L3

Reviews:

Related manuals for SDM-300L3

Brands by name

Popular brands

Comtech EF Data SDM-300L3, Installation And Operation Manual

Search results

Summary of Contents for SDM-300L3

Reviews:

Related manuals for SDM-300L3

Brands by name

Popular brands