manualshive.com logo in svg

Comtech EF Data SDM-300L3, Installation And Operation Manual

Share
Download
Comtech EF Data SDM-300L3 Installation And Operation Manual Download Page 307

14–1 

CHAPTER 14 .  SPECIFICATIONS 

 

14.1 Specifications 

The SDM-300L3 satellite modem specifications are divided into sections as follows.   
 
 

• 

Specifications Summary 

• 

BER Specifications 

• 

Modem Specifications 

• 

Demodulator Specifications 

• 

Interface Specifications 

• 

Terrestrial Interface Types 

• 

System Specifications 

• 

BUC/FSK Communications (Refer to Chapter 15) 

 

Figure 14-1 shows a block diagram of the modem in a typical application. 

 
 

  
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for SDM-300L3

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands