Comtech EF Data SDM-300L3 Installation And Operation Manual Download Page 146

Page: 146 / 408

SDM-300L3 Satellite Modem

Revision 1

Front Panel Operation

MN/SDM300L3.IOM

4–78

FUNCTION SELECT: STORED FLTS/ALMS: OUTDOOR UNIT

OUTDOOR UNIT

_ _ _ _ _

Displays the stored outdoor unit fault or alarm, such as:

•

CURRENT

ODU POWER ON ONLY

•

VOLTAGE

ODU POWER ON ONLY

•

TEMPERATURE

FSK ONLY

•

PLL LOCK

FSK ONLY

•

CHECKSUM

FSK

ONLY

FUNCTION SELECT: STORED FLTS/ALMS:

UNAVAILABLE

SECONDS (CONDITIONAL)

UNAVAL SECONDS

STORED TIME/DATE

IMPORTANT

Conditional:

This is available only with the Reed-Solomon option.

A fault is indicated if the Reed-Solomon Codec could not correct bit errors in one block
of serialized data in any given second.

FUNCTION SELECT: STORED FLTS/ALARMS: CLEAR

CLEAR

STORED FAULTS

To clear the currently logged stored faults, press [ENTER] when the “Clear Stored
Faults/Yes?” selection is displayed.

Summary of Contents for SDM-300L3

























































































































































































































































































































































































































Search results

Summary of Contents for SDM-300L3

Reviews:

Related manuals for SDM-300L3

Brands by name

Popular brands

Comtech EF Data SDM-300L3, Installation And Operation Manual

Search results

Summary of Contents for SDM-300L3

Reviews:

Related manuals for SDM-300L3

Brands by name

Popular brands