SDM-300L3 Satellite Modem
Revision 1
Remote Control Operation
MN/SDM300L3.IOM
A–21
Modulator/
Coder
Config.
Program
Status
Command:
Response:
<add/MCP_'cr'
>add/MCP_'cr'
SMT_xxxxxxx'cr'
ITOT_xxxxx'cr'
MOM_xxxxxxx'cr'
MT_xxxxx'cr'
MET_xxx'cr'
MF_nnn.nnnnnnn'cr'
MF_nnnnn.nnnn'cr'
MR_nnnn_mmmm.mmm'cr'
MPO_snn.n'cr'
LPC_xxx'cr' (Note
10)
MOP_snn.n'cr' (Note
4)
SE_xxx'cr'
DENC_xxx'cr'
ILT_xxx'cr'
ERF_nnnnn.n'cr'
TC_xxxx'cr'
TCP_xxxx'cr'
BBL_xxx'cr'
ILB_xxx'cr'
ICFT_xxxx'cr'
ISP_xxxxxx'cr'
TDF_xxxx'cr'
ISCL_TX1_nnn'cr'
ISCL_TX2_nnn'cr'
TDP_xxxx'cr'
DDF_xxxxxx'cr' (Note
1)
BDCA_dd;cc_dd;cc...'cr' (Note
1)
MRC_xxx'cr'
MSR_xxx'cr'
RSEN_xxx'cr'
BW_TX1_nnn'cr' (Note
2)
BW_TX2_nnn'cr' (Note
2)
BW_TX3_nnn'cr' (Note
2)
BW_TX4_nnn'cr' (Note
2)
TXDR_xxxxxx'cr'
TOBR_nnnnn'cr' (Note
3)
TCCL_n'cr' (Note
3)
TCSB_n'cr' (Note
3)
TOCP_xxxx'cr' (Note
3)
TCT_xxxxx'cr' (Note
3)
NOMP_snn.n'cr' (Note
10)
MINP_snn.n'cr' (Note
10)
MAXP_snn.n'cr' (Note
10)
LCL_xxxx'cr'
(Note 10)
RCL_xxxx'cr' (Note
10)
CTSD_xx'cr'
RTSM_xxx'cr'
TDA_xxx'cr'
COM_xxxxxx'cr'
IDRT_xxxxx'cr' (Note
2)
TRSI_xx'cr'
T310_xxx'cr'
T315_xxx’cr’
ODU_xxx’cr’ (Note 11)
ODUR_xxx’cr’ (Note 11)
ODUL_xxxx’cr’ (Note 11)
ODUH_xxxx’cr’ (Note 11
)
RF_xxx'cr''lf']
System Modem Type
Interface Transmit Overhead Type
Modem Operation Mode
Modulator Type
Modulator Encoder Type
Modulator Frequency (Non L-Band modem)
Modulator Frequency (Non L-Band modem)
Modulator Rate
Modulator Power Offset
AUPC Local Power Enable
Modulator Output Power
Scrambler Enable
Differential Encoder
Interface Loop Timing
External Reference Frequency
Transmit Clock (Source)
Transmit Clock Phase
Baseband Loopback
Interface Loopback
Interface Coding Format Transmit
Interface Substitution Pattern (TX 2047)
Transmit Data Fault
Service Channel Level TX1
Service Channel Level TX2
Transmit Data Phase
Drop Data Format
Bulk Drop Channels Assignment
Modulator Reference Clock
Modulator Spectrum Rotation
Reed-Solomon Encoder
Backward Alarm Enable TX1
Backward Alarm Enable TX2
Backward Alarm Enable TX3
Backward Alarm Enable TX4
TX Driver Type
ASYNC Transmit Overhead Baud Rate
ASYNC Transmit Channel Character Length
ASYNC Transmit Channel Stop Bits
ASYNC Transmit Overhead Channel Parity
ASYNC Transmit Communications Type
AUPC Nominal Power Value
AUPC Minimum Power Value
AUPC Maximum Power Value
AUPC Local Carrier Loss
AUPC Remote Carrier Loss
CTS Delay Time
RTS TX-IF Control Mode
Transmit BPSK Data Ordering
Carrier Only Mode
IDR Transmit ESC Type
IBS Transmit ESC Type
TX Reed-Solomon Interleave Value
TX 8PSK 2/3 IESS-310 Operation
TX IESS-315 Operational Mode
ODU Power
ODU Reference
ODU Current Monitor Low Current Threshold
ODU Current Monitor High Current Threshold
RF Output (ON/OFF)
Note: This command is used by the EF Data M:N protection
switch to collect information that is necessary to configure
back-up modems. Because this command (content and/or
order) can be changed at any time by EF Data, it is advisable
that other commands ('MCS_' and 'ICS_', or 'BCS_') be used
for M&C systems.
