manualshive.com logo in svg

Comtech EF Data SDM-300L3, Installation And Operation Manual

Share
Download
Comtech EF Data SDM-300L3 Installation And Operation Manual Download Page 297

SDM-300L3 Satellite Modem 

Revision 1 

Asynchronous Interface/AUPC MN/SDM300L3.IOM 

11–21 

The local end cable connects the 25-pin female ASYNC connector (on either the 
breakout panel or the Y cable) to the EIA-485 (2-wire) remote terminal (WYSE or laptop 
computer). The pinout of the local cable is listed in the following table. 
 

#7. Local End EIA-485 (2-Wire) 

9-Pin  

Female Connector 

25-Pin  

Male Connector 

TX/RX+ 4 14, 

16 TX+/RX+ 

TX/RX- 5 2, 

3  TX-/RX- 

 
In addition, the following table lists the pinout for the WYSE terminal cable using an  
EIA-232 to EIA-485 converter. 
 

#7. Local End WYSE Cable With Converter 

25-Pin  

Male Connector 

9-Pin  

Male Connector 

TX-/RX- 2, 

5  5 TX/RX- 

TX+/RX+ 14, 

17  4  TX/RX+ 

(See Note)

 

18, 21 

 

 

 

Note:

 Disables RD during TD. 

 
The remote end cable connects the 25-pin female ASYNC connector (on either the 
breakout panel or the Y cable) to the 9-pin female connector, J6, at the rear of the 
modem. The pinout of the remote cable is listed in the following table. 
 

#7. Remote End EIA-232 

9-Pin  

Male Connector 

25-Pin  

Male Connector 

RX 2 2 RX 

TX 3 3 TX 

GND 5 7 GND 

 

Summary of Contents for SDM-300L3

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands