manualshive.com logo in svg

Comtech EF Data SDM-300L3, Installation And Operation Manual

Share
Download
Comtech EF Data SDM-300L3 Installation And Operation Manual Download Page 148

SDM-300L3 Satellite Modem 

Revision 1 

Front Panel Operation 

MN/SDM300L3.IOM 

 

4–80 

  FUNCTION 

SELECT: 

REMOTE AUPC: CONFIGURATION: 

  AUPC 

ENABLE 

(CONDITIONAL) 

 

AUPC ENABLE

OFF

 

 

IMPORTANT

 

Conditional: This menu is available when either the ASYNC or AUPC 
selection is made from the Modem Type menu, located under the 
Utility: Modem Type menu. 

 Requires either the Overhead  Card installed with the ASYNC/AUPC 
option or the Reed-Solomon Card with AUPC option. 

 
Programs the AUPC feature On or Off at the far end of the link. This requires that modems 
at both ends of the link are locked to function. This program is for control or last known 
status. 

  FUNCTION 

SELECT: 

REMOTE AUPC: CONFIGURATION: 

 

 

B-BAND LOOP BACK (CONDITIONAL) 

 

B-BAND LOOP BACK

OFF

 

 
 

IMPORTANT

 

Conditional:

 

This menu is available when either the ASYNC or AUPC 

selection is made from the Modem Type menu, located under the 
Utility: Modem Type menu. 

 Requires either the Overhead  Card installed with the ASYNC/AUPC 
option or the Reed-Solomon Card with AUPC option. 

 
Programs the remote baseband loopback On or Off  at the far end of the link. Modems at 
both ends of the link shall be locked. 
 

Note:

 This program is for control or last known status. 

 
 
 
 
 
 

Summary of Contents for SDM-300L3

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands