Comtech EF Data SDM-300L3 Installation And Operation Manual Download Page 107

Page: 107 / 408

SDM-300L3 Satellite Modem

Revision 1

Front Panel Operation

MN/SDM300L3.IOM

4–39

FUNCTION SELECT: CONFIGURATION: INTERFACE:

INSERT

FORMAT

(CONDITIONAL)

INSERT FORMAT

IMPORTANT

Conditional: This menu is only available when optional D&I have been
selected for Modem Type in the Utility menu and the Overhead Card is
installed.

Selects the desired insert data channel signaling. The choices are:

•

E1_CCS (E1 Common Channel Signaling)

•

E1-CAS (E1 Channel Associated Signaling)

•

E1_31_TS (E1 No Multiframe Sync Alignment)

•

E1_IBS (E1 International Business Service)

•

T1 (T1 Data)

•

T1_IBS (T1 International Business Service)

•

T1_ESF (T1 Extended Super Frame)

•

T1_ESF_S (Special Signaling)

•

T1_S (Special Signaling)

Summary of Contents for SDM-300L3

























































































































































































































































































































































































































Search results

Summary of Contents for SDM-300L3

Reviews:

Related manuals for SDM-300L3

Brands by name

Popular brands

Comtech EF Data SDM-300L3, Installation And Operation Manual

Search results

Summary of Contents for SDM-300L3

Reviews:

Related manuals for SDM-300L3

Brands by name

Popular brands