Comtech EF Data SDM-2020 Installation And Operation Manual Download Page 85

Page: 85 / 215

SDM-2020 Satellite Demodulator

Operation

Rev. 3

3–41

3.3.5.2

Utility Interface Menu

Refer to Figure 3-12.

INTERFACE TYPE

Displays the interface type installed in the demodulator, for example:

•

RS422

•

LVDS

•

ASI/RS422

•

ASI/LVDS

•

ECL/HSSI_RX

•

G.703

•

SMPTE 310M

•

NONE

•

UNKNOWN

Note:

This is a status window only, and no changes can be made from this menu.

Refer to Appendix A for information about the front panel menus for specific interface types.

Note:

As additional data interfaces are introduced, they are added to the menu. If an interface is

not recognized, then UNKNOWN is displayed. In this case, a later version of firmware may be
required to operate with the data interface.

Summary of Contents for SDM-2020
























































































































































































































Search results

Summary of Contents for SDM-2020

Reviews:

Related manuals for SDM-2020

Brands by name

Popular brands

Comtech EF Data SDM-2020, Installation And Operation Manual

Search results

Summary of Contents for SDM-2020

Reviews:

Related manuals for SDM-2020

Brands by name

Popular brands