background image

SDM-2020 Satellite Demodulator

Introduction

Rev. 3

1–7

1.2.3 FAST 

Options

Certain options are enabled using EFData’s Fully Accessible System Topology (FAST)
features described in Appendix C. The software requirements for the FAST options are
also listed in Appendix C. Options include:

 

Original Equipment Manufacturer (OEM) LCD (See Appendix B)

 

8PSK – DVB

 

16QAM – DVB

 

2 L-Band Inputs

 

4 L-Band Inputs

1.3 Specifications

1.3.1 Demodulator

Table 1-7 describes the demodulator specifications.

Table 1-7.  Demodulator Specifications

General Specifications

Transmission Format

QPSK per EN 300 421
Optional – 8PSK and 16QAM per EN 301 210

BER Performance

See paragraph 1.4.

Notes:

1.

 

Values shown for 8PSK 8/9 are for symbol rates 

 30 Msym/s.

2.

 

For 8PSK 8/9 at symbol rate > 30 Msym/s, add 0.4 dB.

Data Rate/Symbol Rate

1.5 to 100 Mbit/s in 1 bit/s increments depending upon symbol rate and data
interface, see Table 1-1, Table 1-2, and Table 1-3.

Equivalent Serial Data Rate at 96 DIN
Connector

Minimum and maximum data rate and symbol rates,
see Table 1-1, Table 1-2, and Table 1-3.
Framing
187

Data Rate = SR x m x CRv x (187/204)

188

Data Rate = SR x m x CRv x (188/204)

204

Data Rate = SR x m x CRv x (204/204)
SR = Symbol Rate
m = 2 QPSK, 3 8PSK, 4 16QAM

 CRv = Viterbi/trellis code rate 1/2, 2/3, 3/4, 5/6, 7/8, and 8/9

Data Rate Tolerance

Programmed rate 

±

 100 ppm

Modulation Type and Inner Code Rate

QPSK: 1/2, 2/3, 3/4, 5/6, 7/8
Optional - 8PSK: 2/3, 5/6, 8/9
Optional - 16QAM 3/4, 16QAM 7/8

Outer Code Rate (Reed-Solomon)

RS (204, 188, t = 8) per EN 300 421 and EN 301 210

Deinterleaving

Depth 12, per EN 300 421 and EN 301 210

Spectral Shaping

Square-root raised cosine, 

 = 0.35 per EN 300 421 and EN 301 210

Energy Dispersal

EN 300 421 and EN 301 210, or None

Summary of Contents for SDM-2020
























































































































































































































Reviews: