Comtech EF Data SDM-2020 Installation And Operation Manual Download

Page: 37 / 215

SDM-2020 Satellite Demodulator

Installation

Rev. 3

2–5

Note:

After a different interface type has been installed, the demodulator recognizes the

change upon power up, and defaults to valid parameters for the new interface.

2.2.1.1

Data Interface Removal

Disconnect power from the demodulator.

Use a Phillips



screwdriver to loosen the two captive screws on the faceplate of the

data interface.

Grasp the data interface by the faceplate handle.

Carefully pull the data interface out of the slot.

2.2.1.2

Data Interface Installation

Disconnect power from the demodulator.

Grasp the data interface by the faceplate handle.

Locate the opening at the rear of the demodulator.

Carefully align the data interface with the card guides inside the demodulator and
insert the data interface into the opening.

Push the data interface firmly into the slot to ensure a good connection.

Align the captive screws located on the faceplate with the holes on the demodulator
rear panel.

Use a Phillips



screwdriver to tighten the screws.

Summary of Contents for SDM-2020
























































































































































































































Search results

Summary of Contents for SDM-2020

Reviews:

Related manuals for SDM-2020

Brands by name

Popular brands

Comtech EF Data SDM-2020, Installation And Operation Manual

Search results

Summary of Contents for SDM-2020

Reviews:

Related manuals for SDM-2020

Brands by name

Popular brands