Comtech EF Data SDM-2020 Installation And Operation Manual Download Page 76

Page: 76 / 215

Operation

SDM-2020 Satellite Demodulator

3–32

Rev. 3

3.3.5 Utility

Menus

The Function Select Utility menu is divided into the following categories:

•

Demodulator

•

Interface

•

System

•

Demodulator Options

•

Factory Setup - (Factory Use Only)

After entering the Utility functions level, press [

←

] or [

→

] to select the desired Utility

menu, and press [ENTER]. Press [

←

] or [

→

] to select the utility function of interest.

Notes:

1. The Utility Factory Setup menu is for

EFData

service personnel only.

Unauthorized access may cause the demodulator to operate incorrectly.

Changes in the Utility menu may cause changes in other front panel menus.

Summary of Contents for SDM-2020
























































































































































































































Search results

Summary of Contents for SDM-2020

Reviews:

Related manuals for SDM-2020

Brands by name

Popular brands

Comtech EF Data SDM-2020, Installation And Operation Manual

Search results

Summary of Contents for SDM-2020

Reviews:

Related manuals for SDM-2020

Brands by name

Popular brands