Remote Control Operation
SDM-2020 Satellite Demodulator
B–10
Rev. 3
Demod/
Coder
Config.
Program
Status
Command:
Response:
<add/DCP_'cr'
>add/DCP_'cr'
ISEL_xxxxxx'cr'
(Notes 1, 2)
ICLK_xxx'cr'
(Note 3)
RDVB_xxxx'cr'
DF_nnnn.nnnn'cr'
DR_nnnn_mmm.mmmmmm'cr'
DE_xxx'cr'
RCP_xxx'cr'
RDP_xxxx'cr'
RDF_xxxx'cr'
SWR_nnnnnnnn'cr'
SR_xxx'cr'
DM_xxx'cr'
(Notes 1, 2)
RR_xxx'cr'
(Notes 1, 2)
MC_xxx’cr’
(Note 2)
ERF_nnnnn.nnn’cr’
(Note 4)
TRF_nnnnn.n’cr’
(Note 4)
ILB_xxx’cr’
(Note 4)
ICFR_xxxx’cr’
(Note 4)
BC_xxx’cr’
(Note 4)
IBS_nn’cr’
(Note 4)
IRFS_1544_SSSS’cr’
(Note 4)
IRFS_2048_SSSS”cr’
(Note 4)
IRFS_6312_SSSS’cr’
(Note 4)
IRFS_8448_SSSS’cr’
(Note 4)
IRFS_32064_SSSS’cr’
(Note 4)
IRFS_34368_SSSS’cr’
(Note 4)
IRFS_44736_SSSS’cr’
(Note 4)
IRFS_51840_SSSS’cr’'lf']
(Note 4)
RFIN_xx’cr’
(Note 6)
LNBV_xx’cr’’lf’]
(Note 6)
Interface Select
Interface Mode
DVB Framing Type
Demodulator Frequency
Demodulator Rate
Descrambler Enable
Receive Clock Phase
Receive Data Phase
Receive Data Fault
Sweep Width Range
Sweep Reacquisition
DM State Control
RR State Control
MC State Control
External Reference Frequency
TX Terrestrial Clock Frequency
Interface Loopback
Interface Coding Format Receive
Buffer Clock Source
Interface Buffer Size
Interface Receive Frame Structure 1544
Interface Receive Frame Structure 2048
Interface Receive Frame Structure 6312
Interface Receive Frame Structure 8448
Interface Receive Frame Structure 32064
Interface Receive Frame Structure 34368
Interface Receive Frame Structure 44736
Interface Receive Frame Structure 51840
RF Input Select
LNB Voltage Select
Notes:
1.
Only displayed when RS422 interface is
installed.
2.
Only displayed when ASI/RS422 interface is
installed.
3.
Not displayed when ASI/RS422 or G.703
interface is installed.
4.
Only displayed when G.703 interface installed.
5. Not
Used.
6.
Only displayed if the 4-channel RF card is
installed.
This command is used by the EFData M:N protection
switch to collect information that is necessary to
configure back-up demodulators. Because this
command (content and/or order) can be changed at
any time by EFData, it is advisable that other
commands ('DCS_' and 'ICS_', or 'BCS_') be used for
M&C systems.
Summary of Contents for SDM-2020
