Comtech EF Data SDM-2020 Installation And Operation Manual Download Page 13 | Manualshive

Page: 13 / 215

background image

Preface

SDM-2020 Satellite Demodulator

xii

Rev. 3

Conventions and References

Cautions and Warnings

CAUTION

CAUTION indicates a hazardous situation that, if not avoided, may result in
minor or moderate injury. CAUTION may also be used to indicate other
unsafe practices or risks of property damage.

WARNING

WARNING indicates a potentially hazardous situation that, if not avoided,
could result in death or serious injury.

Metric Conversion

Metric conversion information is located on the inside back cover of this manual. This
information is provided to assist the operator in cross-referencing English to Metric
conversions.

Recommended Standard Designations

Recommended Standard (RS) Designations have been superseded by the new designation
of the Electronic Industries Association (EIA). References to the old designations are
shown only when depicting actual text displayed on the screen of the unit (RS-232, RS-
485, etc.). All other references in the manual will be shown with the EIA designations
(EIA-232, EIA-485, etc.) only.

Trademarks

Other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.

Reporting Comments or Suggestions Concerning this Manual

Comments and suggestions regarding the content and design of this manual will be
appreciated. To submit comments, please contact the Comtech EFData Customer Support
Department.

«
...
11
12
13
14
15
...
»

Summary of Contents for SDM-2020
























































































































































































































Reviews:

No comments

Related manuals for SDM-2020

Brand: Teknoline Pages: 23

Brand: Velleman Pages: 12

Brand: Citizen Pages: 16

Brand: PVI Pages: 35

Brand: LEXIBOOK Pages: 142

Brand: LEXIBOOK Pages: 158

Brand: Nextech Pages: 2

Micro line MLC-300

Brand: Lemco Pages: 2

Brand: Pico Macom Pages: 8

Brand: NetMedia Pages: 2

Brand: Labgear Pages: 4

Brand: Sharp Pages: 2

Brand: Casio Pages: 13

Brand: TELELYNX Pages: 30

Brand: ScatterBox Pages: 2

Brand: Nyrius Pages: 20

Brand: Aiphone Pages: 2

Brand: Aiphone Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands