Comtech EF Data SDM-2020 Installation And Operation Manual Download Page 46

Page: 46 / 215

Operation

SDM-2020 Satellite Demodulator

3–2

Rev. 3

3.2 Front

Panel

The demodulator front panel (Figure 3-1), enables the user to control demodulator
configuration parameters and display the demodulator status.

Demodulator

ALARMS

FAULTS

RECEIVE

POWER ON

ENTER

CLEAR

CARRIER DETECT
TEST MODE

SYNC

STORED

ADAPTIVE BROAD BAND

Figure 3-1. Front Panel

The front panel features include:

•

6-button keypad for local control

•

7-LEDs to provide overall status at a glance

•

32-character, 2-line LCD display

All functions are accessible at the front panel by entering one of five pre-defined
Function Select categories:

•

Configuration

•

Monitor

•

Faults/Alarms

•

Stored Faults/Alarms

•

Utility

Summary of Contents for SDM-2020
























































































































































































































Search results

Summary of Contents for SDM-2020

Reviews:

Related manuals for SDM-2020

Brands by name

Popular brands

Comtech EF Data SDM-2020, Installation And Operation Manual

Search results

Summary of Contents for SDM-2020

Reviews:

Related manuals for SDM-2020

Brands by name

Popular brands