manualshive.com logo in svg

ComSifter CS-8D Pro, User Manual, Page: 112 / 245

Share
Download
ComSifter CS-8D Pro User Manual Download Page 112

C O N F I G U R I N G   C O M S I F T E R  

User Guide  |  

ComSifter CS-8D Pro

  

3–80 

Determining the True Connection Speed  

For ComSifter to effectively control the upstream buffer, it must know the true speed of the upstream 
connection. Advertised ISP speeds are typically the sync rate of the cable/DSL modem. These rates do not 
include the protocol between the cable/DSL modem and the ISP, or the TCP/IP protocol used over the 
Internet. These protocols may cumulatively add 15-20% overhead. An advertised speed of 128Kbps upstream 
may only be able to move customer data at 102Kbps. Since ComSifter QOS is buffering customer data, it will 
need to use the 102Kbps, not the advertised 128Kbps.  

The best method to determine the upload speed of your network is to use a connection test provided by a third 
party. The following links will take you to locations on the Internet providing connection tests. 

www.dslreports.com/stest

 

http://www.speakeasy.net/speedtest/ 

http://www.dsl-speed.org/test.htm 

Note:

 

Speed tests should only be run when your network is not being used; such as 
early in the morning or late at night. It is also suggested that multiple tests be 
run to insure repeatability. 

 

Figure 3-85

: Results of Speed Test

 

In the example above, we ran a speed test from 

www.dslreports.com/stest

 . Upstream speed was 309Kbps. 

We will take 1% off this figure (306) and use it as our Up Speed in ComSifter 

QOS incorporates three Queues. These are Default (no user control), High Priority, and Low priority. A fourth 
queue, called Special Network, is available in the event that ComSifter is routing into another network that is a 
part of your LAN. Each of these queues has two parameters: a rate, and a ceiling. The rate of a queue is the 
transmission speed of the queue when there is traffic in a higher priority queue. Ceiling is the maximum 
transmission speed of the queue when traffic is not present in a higher priority queue. 

By default, all traffic starts in the Default Queue. The Default Queue is calculated at one-quarter of the Up 
Speed. If the Low and Highest Queues are not defined, then the traffic in the Default Queue will share equally 
the bandwidth defined in Ceiling. If the Low or High Priority Queues are defined, then traffic in those queues 
will get more bandwidth than the default Queue. In the example shown below, ports 25 (SMTP), 465 (secure 
SMTP), and 80 (web browsing) have been given extra bandwidth by being moved to the Low Priority Queue. 
Port 53 (DNS) has been moved to the High Priority Queue giving DNS lookups the most bandwidth. 

Note:

 

ComSifter is configured to automatically move ACK packets and short packets 
(less than 1000 bytes) into the highest priority queue. This insures that uploads 
will not adversely affect downloads. 

 

Summary of Contents for CS-8D Pro






















































































































































































































































Reviews:

No comments