ComAp intelilite nt amf20 Reference Manual Download

Page: 36 / 145

InteliLite

– AMF20/25, SW version 2.2, ©ComAp – September 2014 36

IL-NT-AMF-2.2-Reference Guide.pdf

Earth Fault measurement (module)

The Earth Fault protection is done by extension module IC-NT CT-BIO7.

Technical characteristics

Input current range up to 5 A (

IC-NT CT-BIO7

)

Measurement range from 1 to 500 A

Operating frequency 50 or 60 Hz

Tripping current software programmable from 1 to 500 A or DISABLED

Tripping delay software programmable from 0,03 to 5 seconds

Included seven binary inputs or seven binary outputs (IL-NT-CT-BIO7)

Hint:

For more technical details see

IC-NT CT-BIO7 interface

Hint:

For more information about the application settings see

EarthFaultProt

setpoint group

Operating principle

When the measured current exceeds the set value, this indicates that part of the current is dispersed
to earth and after the set

Earth Fault Del

then

Earth Fault Sd

protection and

AL EarthFault

output are

activated. Earth Fault protection is not active when gen-set does not run and also when

EF Protection

DISABLED.

Summary of Contents for intelilite nt amf20


















































































































































Search results

Summary of Contents for intelilite nt amf20

Reviews:

Related manuals for intelilite nt amf20

Brands by name

Popular brands

ComAp intelilite nt amf20, Reference Manual

Search results

Summary of Contents for intelilite nt amf20

Reviews:

Related manuals for intelilite nt amf20

Brands by name

Popular brands