ComAp intelilite nt amf20 Reference Manual Download

Page: 137 / 145

InteliLite

– AMF20/25, SW version 2.2, ©ComAp – September 2014 137

IL-NT-AMF-2.2-Reference Guide.pdf

Maintenance

Backup battery replacement

The internal backup battery should be replaced approx. every 5-7 years. Replace the battery, if the
alarm

Low BackupBatt

occurs. Follow these instructions:

1. Disconnect all terminals from the controller and remove the controller from the switchboard.
2. Release the rear cover using a flat screwdriver or another suitable tool.

3. Remove all plug-in modules.
4. The battery is located in a holder on the circuit board. Remove the old battery with a small

sharp screwdriver and push with a finger the new battery into the holder. Use only CR1225
lithium battery.

Summary of Contents for intelilite nt amf20


















































































































































Search results

Summary of Contents for intelilite nt amf20

Reviews:

Related manuals for intelilite nt amf20

Brands by name

Popular brands

ComAp intelilite nt amf20, Reference Manual

Search results

Summary of Contents for intelilite nt amf20

Reviews:

Related manuals for intelilite nt amf20

Brands by name

Popular brands