ComAp intelilite nt amf20 Reference Manual Download

Page: 100 / 145

InteliLite

– AMF20/25, SW version 2.2, ©ComAp – September 2014 100

IL-NT-AMF-2.2-Reference Guide.pdf

State

Condition of the transition

Action

Next state

Cranking

RPM>

Starting RPM

STARTER off
PRESTART off

Starting

D+ input activated or oil pressure detected
or Gen voltage > 25% Vgnom

STARTER off
PRESTART off

Starting

MaxCrank Time

elapsed, 1st attempt

STARTER off
FUEL SOLENOID off
STOP SOLENOID on

CrankFail Pause

timer

started

Crank pause

MaxCrank Time

elapsed, last attempt

STARTER off
PRESTART off

Shutdown (Start
fail)

Crank
pause

CrankFail Pause

elapsed

STARTER on
FUEL SOLENOID on

STOP SOLENOID off

MaxCrank Time

counter

started

Cranking

Starting

80%

Nominal RPM

reached

READY TO LOAD on

Min, Max Stab Time

counter started

Running

RPM = 0 or any other shutdown condition

FUEL SOLENOID off
STOP SOLENOID on

Shutdown

60 sec.

Elapsed

FUEL SOLENOID off
STOP SOLENOID on

Shutdown (Start
fail)

Running

Stop request

READY TO LOAD off

Cooling Time

timer

started

Cooling

RPM = 0 or any other shutdown condition

READY TO LOAD off

FUEL SOLENOID off

Shutdown

GCB CLOSE/OPEN

closed

Loaded

Loaded

GCB CLOSE/OPEN

opened

Running

RPM = 0 or any other shutdown condition

FUEL SOLENOID off
STOP SOLENOID on
READY TO LOAD off

Shutdown

Cooling

Cooling Time

elapsed

FUEL SOLENOID off
STOP SOLENOID on

Stop

RPM = 0 or any other shutdown condition

FUEL SOLENOID off
STOP SOLENOID on

Shutdown

Start request

READY TO LOAD on

Running

Stop

RPM = 0,

Oil pressure not detected, Vgen <

10V, D+ not active

Ready

If at least one of engine running indication is
detected when Setpoint Stop Time elapsed.
See more details in chapter Gen-Set
Operation state

–

Stop engine conditions

Stop (Stop fail)

if all generator parameters OK and Min Stab Time elapsed, indicates that GCB is possible to close.

In AUTO Mode closes in this moment GCB automatically

If GCB output used GCB opens automatically

The start-up sequence can be interrupted in any time by coming stop request

Fuel solenoid is switched on with time advance of 1s fixed before starter motor is switched on.

Hint:

Summary of Contents for intelilite nt amf20


















































































































































Search results

Summary of Contents for intelilite nt amf20

Reviews:

Related manuals for intelilite nt amf20

Brands by name

Popular brands

ComAp intelilite nt amf20, Reference Manual

Search results

Summary of Contents for intelilite nt amf20

Reviews:

Related manuals for intelilite nt amf20

Brands by name

Popular brands