ComAp intelilite nt amf20 Reference Manual Download

Page: 110 / 145

InteliLite

– AMF20/25, SW version 2.2, ©ComAp – September 2014 110

IL-NT-AMF-2.2-Reference Guide.pdf

Electric state machine

MainsOper

Mains is present and all its values are within limits.
(MCB is closed, GCB is opened)

MainsFlt

Mains cut off

– immediate state

MainsFlt

Mains cut off

– takes EmergStart del

IslOper

Island operation (MCB is opened, GCB is closed)

MainsRet

Mains recover

Brks Off

GCB, MCB opened

MinStabTO

Minimal Stabilization Timeout for electric protections

MaxStabTO

Maximal Stabilization Timeout for electric protections

Trans Del

Forward return break delay. Delay between GCB opening and MCB closing

List of possible events

Events specification

Protection

type

Information on binary
output available (See

list of

Binary outputs

)

Description

AI1 Wrn

WRN

YES

Value measured on analog input 1 is
lower than

AI1 Wrn

setpoint.

AI1 Sd

YES

Value measured on analog input 1 is
lower than

AI1 Sd

setpoint.

AI2 Wrn

WRN

YES

Value measured on analog input 2 is
greater than

AI2 Wrn

setpoint.

AI2 Sd

YES

Value measured on analog input 2 is
greater than

AI2 Sd

setpoint.

AI3 Wrn

WRN

YES

Value measured on analog input 3 is
greater than

AI3 Wrn

setpoint.

AI3 Sd

YES

Value measured on analog input 3 is
greater than

AI3 Sd

setpoint.

IOM AIx Wrn

WRN

YES

Warning alarm configurable on the
input of IG-IOM/IGS-PTM.

IOM AIx Sd

YES

Shutdown alarm configurable on the
input of IG-IOM/IGS-PTM.

Binary input

Configurable

YES

Configurable Warning/BOC/Shutdown
alarms on the inputs of IL-NT.

IOM Bin Inp

Configurable

YES

Configurable Warning/BOC/Shutdown
alarms on the inputs of IG-IOM/IGS-
PTM.

IL-NT-BIO8

Configurable

YES

Configurable Warning/BOC/Shutdown
alarms on the inputs of IL-NT-BIO8.

ActCallCH1Fail

WRN

Active call on channel 1 failed.

ActCallCH2Fail

WRN

Active call on channel 2 failed.

Low BackupBatt

WRN

RTC backup battery is flat

Wrn Batt Volt

WRN

YES

Battery voltage is out of limits given by

Batt Undervolt/Batt OverVolt

setpoints.

ChargeAlt Fail

WRN

YES

Failure of alternator for charging the
battery.

Sd BatteryFlat

YES

If the controller switches off during
starting sequence due to bad battery
c

ondition it doesn’t try to start again

and activates this protection.

Sd Start Fail

YES

Gen-set start failed. All crank attempts
were tried without success.

Wrn Stop Fail

WRN

YES

Gen-set stop failed. See description at

Gen-set Operation States

chapter.

Sd Gen Lx >V

YES

The generator voltage is out of limits

Summary of Contents for intelilite nt amf20


















































































































































Search results

Summary of Contents for intelilite nt amf20

Reviews:

Related manuals for intelilite nt amf20

Brands by name

Popular brands

ComAp intelilite nt amf20, Reference Manual

Search results

Summary of Contents for intelilite nt amf20

Reviews:

Related manuals for intelilite nt amf20

Brands by name

Popular brands