ComAp IG-NT GC Reference Manual Download | Manualshive

Page: 223 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

223

functions:

N

ONE

S

HOW

H

IDE

No action
regarding this
screen
instrument is
taken.

By default the screen
instrument is hidden. If any
of mask inputs (

or other

switches) connected to this
particular screen instrument
is activated, this screen
instrument is shown.

By default the screen
instrument is shown. If any of
mask inputs (

or other

switches) connected to this
particular screen instrument
is activated, this screen
instrument is hidden.

E.g. this function can be used to "swap" between two different screen instruments
when certain conditions are fulfilled. Logical binary inputs Mask 1..4 can be used
to define any custom condition for this "swapping" function.

Table of analog input functions

Analog input: LCD brightness

Related FW

3.0

Description

This functional input is used to adjust the backlight intensity of the

IG-NT built-in

terminal (display) by an analog input (e.g. a potentiometer). If this input is
configured to a physical analog input or other value, the brightness adjusted by
buttons at the terminal is overriden by this analog input.

Analog input: MLC:AnExSysBld

Related FW

3.0

Description

This functional input is used for requesting the

system baseload

externally by an

analog input. The setpoint

SysBaseLdMode

must be set to EXTERNAL to read

the system baseload from this input.

N

OTE

:

This logical analog input must be configured at each gen-set to the identical
source. The

shared peripherial modules

can be used to distribute the value over

the controllers via the CAN2 bus. See the note in the description of the setpoint

SysBaseLdMode

Analog input: MPF:AnExSysBPF

Related FW

3.0

Description

This functional input is used for requesting the

system power factor

externally by

an analog input. The setpoint

SysBasePFMode

must be set to EXTERNAL to read

the requested system power factor from this input.

N

OTE

:

This logical analog input must be configured at each gen-set to the identical

«
...
221
222
223
224
225
...
»

Summary of Contents for IG-NT GC





































































































































































































































































Reviews:

No comments

Related manuals for IG-NT GC

Brand: ABB Pages: 2

Brand: Samson Pages: 78

Brand: Rachio Pages: 16

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

Brand: Uclear Pages: 40

Brand: TCS Pages: 16

Brand: Parker Pages: 54

Brand: RAM Pages: 71

Brand: B&G Pages: 19

Brand: Parker Pages: 4

Brand: Fuji Electric Pages: 12

Brand: heat-timer Pages: 36

AQUASNAP 30RA "B"

Brand: Carrier Pages: 36

Freedom Bridge FB3

Brand: Identiv Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands