31
Р
у
сс
к
и
й
It
a
lia
n
o
E
n
g
lis
h
D
e
u
tc
h
F
ra
n
ça
is
Shortcut commands while in standby mode
Shortcut commands while in standby mode
Shortcut commands while in standby mode
Shortcut commands while in standby mode
1
Blast freezing
2
Start
Detailed commands sequence
Detailed commands sequence
Detailed commands sequence
Detailed commands sequence::::
1.
Make sure the appliance is in standby
standby
standby
standby mode (6.1
6.1
6.1
6.1).
2.
Insert the needle probe in the product to be chilled (10.0
10.0
10.0
10.0).
3.
Press button
to select the blast freezing cycle.
•
The led button
comes on.
•
Display DY1
DY1
DY1
DY1 gives the setpoint of the air in the compartment (----38°C
38°C
38°C
38°C).
•
Display DY2
DY2
DY2
DY2 reads “---
---
---
---”.
4.
Press button
to start the blast freezing cycle.
•
The led button
comes on.
•
The compressor only starts working 5
working 5
working 5
working 5 seconds after key
is pressed (pump-down 6666.4
.4
.4
.4)
•
DY1
DY1
DY1
DY1 gives needle probe temperature, and DY2
DY2
DY2
DY2 the cycle time remaining, counting down from 240
240
240
240
minutes.
•
If you press button
while the cycle is running, you can view the time elapsed since it started.
5.
A buzzer sounds to advise that the blast chilling cycle has finished.
6.
At the end of the cycle, holding mode starts and continues indefinitely at a holding temperature of ----20°C
20°C
20°C
20°C.
•
The led button
flashes.
•
If you press button
during holding time, you can view the time of the cycle just completed to see
how long it took.
•
The holding stage must last only as long as strictly necessary.
7.
To exit holding mode, press button
.
•
The led button
goes off.
•
The compressor stops 5555 seconds after button
is pressed (pump-down 6.4
6.4
6.4
6.4).
Important
Important
Important
Important
•
Countdown starts when core temperature measured by the needle probe drops below +65°C.
•
When a blast freezing cycle is started, the compressor works non-stop until air temperature in the
compartment reaches ----38°C
38°C
38°C
38°C. After this, it can cycle on and off to keep this temperature constant.
•
The blast freezing cycle ends when the product's core temperature measured by the needle probe reaches
----18°C.
18°C.
18°C.
18°C. The cycle cannot last more than 240 minutes
240 minutes
240 minutes
240 minutes.
8.0
TIME-BASED BLAST CHILLING/BLAST FREEZING
8.1
TIME-BASED SOFT BLAST CHILLING
The time-based soft
soft
soft
soft blast chilling cycle is controlled by the timer.
Shortcut commands while in standby mode
Shortcut commands while in standby mode
Shortcut commands while in standby mode
Shortcut commands while in standby mode
1
Soft blast chilling
2
Time-based cycle
3
Start
Detailed commands sequence
Detailed commands sequence
Detailed commands sequence
Detailed commands sequence::::
1.
Make sure the appliance is in standby
standby
standby
standby mode (6.1
6.1
6.1
6.1).
2.
Press button
to select the soft
soft
soft
soft blast chilling cycle.
•
The led button
comes on.
•
Display DY1
DY1
DY1
DY1 gives the setpoint of the air in the compartment (----2°C
2°C
2°C
2°C).
Summary of Contents for W10T
